Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum upgrade!
It is currently Thu Apr 18, 2019 5:38 pm

All times are UTC-07:00




Post new topic  Reply to topic  [ 2 posts ] 
Author Message
PostPosted: Sun Feb 10, 2019 10:10 am 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 2557
Location: Indianapolis
Car Model*:
I have the steering column out of the 68 Barracuda while other work is being done on the car.

I came across the article linked below

https://www.forabodiesonly.com/mopar/am ... heaper.66/

The steering shaft turned OK, but the outside of the car the bearings felt and sounded dry, so I tore into it.

Found the upper bearing at Vans

https://vansauto.com/product/62-83-uppe ... n-bearing/

15.00 + 7.50 shipping, for size it is an exact replacement and unlike the oe bearing is a sealed unit.

Got the lower bearing, same style as in the FABO link from AMAZON

was 9.49 shipped,, a great value,

Disassembly and installation was very straight forward.
I did need to remove some slight excess metal in the lower column housing and clear the ID of the
bearing slightly to get the ER-16 bearing to fit, nothing extreme, a couple of zips with a sanding roll on a
a gun and all was fine.

The one addition that I made that was not mentioned in the FABO article, and mine is a auto floor shift column.
The lower OE bearing has a recess in it that allows the inner steering column shaft tube to print into it
and center the inner steering shaft tube to the outer column tube. The ER-16 Bearing does not have that feature.

The ER-16 bearing has an up set, or raised inner hub that nicely matched the diameter of the
inner steering column shaft tube. However it does not hold the inner steering shaft tube centered and
overall the ER-16 bearing is about 1/16 of an inch tool long if one wants the raised retainer on the
ER-16 bearing to fit flush to the outer steering column tube.

EZ fixes:
for the length issue, I trimmed the inner steering column tube length, some of this issue is likely part and assembly stack up,
so measure closely and cut once, mine is a nice solid press to stop fit.

for the centering issue, I had some two part RTV-urethane rubber mix left over from making the slant six port molds, used that
to make a nice semi-flexable spacer to bridge the gap between the inner and outer steering column tubes and center them together.
One could use other methods ranging from wraps of duct tape to rubber bushings, or perhaps yours will center better.
But the fix described worked for me.

With the column back together, I cannot say it turns more easily, as it was not locked up or sticky before,
but I can say it turns silently, there is not the dry bearing sound. And it certainly feels better.


Attachments:
File comment: bearings new and old
sc bearins.jpg
sc bearins.jpg [ 32.27 KiB | Viewed 553 times ]
File comment: urethane bushing added to center inner column tube
SC urethane cushion.jpg
SC urethane cushion.jpg [ 23.12 KiB | Viewed 553 times ]
File comment: steering column shaft lower bearing end
ss bearing end.jpg
ss bearing end.jpg [ 19.08 KiB | Viewed 553 times ]
File comment: Steering column shaft after rebuild
steering shaft.jpg
steering shaft.jpg [ 17.46 KiB | Viewed 553 times ]
Top
   
PostPosted: Mon Feb 11, 2019 5:19 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 11853
Location: Park Forest, Illinoisy
Car Model*: 68 Valiant
Good work John!

_________________
Official Cookie and Mater Tormentor.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 2 posts ] 

All times are UTC-07:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited