Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum upgrade!
It is currently Fri Jan 24, 2020 6:16 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 14 posts ] 
Author Message
PostPosted: Thu Jan 09, 2020 10:33 pm 
Offline
1 BBL (New)
User avatar

Joined: Thu Jul 09, 2015 11:19 pm
Posts: 5
Car Model*: 1984 dodge D150 slant6 single cab long be step-sid
Howdy all! :D So I have a 1984 2wd dodge d150 single cab longbed stepstide, with a slant 6. A few years ago I removed the independent suspension due to damage and put in a Dana 44. What I’m wanting to know is if there is a transfer case that fits my 4 speed A833 tranny and if not, what manual transmission will fit the slant 6 engine that will take a transfer case with little to no modifications so I can turn my truck into a 4wd Because I’m moving to a snowy state soon. Any help is greatly appreciated! Thanks!


Top
   
PostPosted: Thu Jan 09, 2020 10:54 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7355
Location: SW Washington
Car Model*: 1954 Dodge C1-B8
The A833/A833OD was never offered in a 4x4. You could use one with a divorced transfer case as with the 1971 and older trucks, but it would be far easier to find and mount the NP435 transmission and transfer case. The NP435 was offered in 2WD trucks so even if you can't find a slant six 4x4 you can get a trans and transfer case from a V8 truck and swap the bellhousing.

Are you sure you have the A833OD? I would have expected a D150 to have the NP435 top-loader.

_________________
Joshua


Top
   
PostPosted: Fri Jan 10, 2020 6:12 am 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9610
Location: Salem, OR
Car Model*:
Quote:
get a trans and transfer case from a V8 truck and swap the bellhousing.


Just to specify you can get the transmission and transfer case from the V-8 truck,
you will need the bellhousing, flywheel and starter from a slant six truck...as they are
all unique to this powertrain combination on a slant.

I also would expect the 80's D-150 to have the low mount starter 143 tooth flywheel
and NP-235/435 combination....


Top
   
PostPosted: Fri Jan 10, 2020 4:14 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 7344
Location: Silver Springs, Fl.
Car Model*:
Joshie225 wrote:

Are you sure you have the A833OD? I would have expected a D150 to have the NP435 top-loader.


Would the 84 d-100 and the d-150 have the same or different drivetrain? My 84 d-100 has a 225 slant, and a A833OD trans. I think it is original to the truck. However it does have a 8 3/4 rear, which I don't think is original.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 225 nitrous
64 Valiant Signet
64 Valiant 4dr 170


Top
   
PostPosted: Fri Jan 10, 2020 4:38 pm 
Offline
1 BBL (New)
User avatar

Joined: Thu Jul 09, 2015 11:19 pm
Posts: 5
Car Model*: 1984 dodge D150 slant6 single cab long be step-sid
Thank you for the responses! Okay so just to clarify:
1- I need to get the NP435 and transfer case from a v8 (can y’all clarify what year and model dodges they are in?)

2- can I keep my original clutch&clutch fork assembly, flywheel and bell housing that I have now? Or do I need different stuff?

3- to answer yalls questions, yes it has from stock the A833OD and also it has a high mount starter.

I don’t have a lot of knowledge on this and I want to make this as easy as possible so I’d like to know Everything I would need and where or what to get it from. Thanks again for all the help!


Last edited by clppanthers on Fri Jan 10, 2020 4:49 pm, edited 1 time in total.

Top
   
PostPosted: Fri Jan 10, 2020 4:47 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7355
Location: SW Washington
Car Model*: 1954 Dodge C1-B8
1. No. You don't need a trans and transfer case from a V8 truck, but it will likely be easier to find. Ideally you'd find a /6 truck so that you can get everything between the engine and the axles including drive shafts, shifters, mounts, etc. This may not be economically feasible unless you find a cheap parts truck.

2. No. Everything as indicated above includes the /6 specific 130 or 143-tooth flywheel, clutch, release mechanism, bellhousing, etc as None of the 122-tooth A833OD stuff interchanges.

_________________
Joshua


Last edited by Joshie225 on Sun Jan 19, 2020 3:17 pm, edited 1 time in total.

Top
   
PostPosted: Fri Jan 10, 2020 4:52 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7355
Location: SW Washington
Car Model*: 1954 Dodge C1-B8
Charrlie_S wrote:
Joshie225 wrote:

Are you sure you have the A833OD? I would have expected a D150 to have the NP435 top-loader.


Would the 84 d-100 and the d-150 have the same or different drivetrain? My 84 d-100 has a 225 slant, and a A833OD trans. I think it is original to the truck. However it does have a 8 3/4 rear, which I don't think is original.


The D150's have a lot higher GVW than the D100s and the A833OD is pretty light duty which informed my assumption. I wonder if the D100 in question has one of the rare late bellhousings that use a larger clutch? I think the 8 3/4 was done by 1974.

_________________
Joshua


Top
   
PostPosted: Fri Jan 10, 2020 5:17 pm 
Offline
1 BBL (New)
User avatar

Joined: Thu Jul 09, 2015 11:19 pm
Posts: 5
Car Model*: 1984 dodge D150 slant6 single cab long be step-sid
Do you know what years the /6 had the NP435? Because I’m going to go check the local salvage yard


Top
   
PostPosted: Fri Jan 10, 2020 7:20 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 2862
Location: Indianapolis
Car Model*:
My ‘83 D150: slant, factory BBD/2bbl, 8.25 rear axel and A833 OD


Top
   
PostPosted: Fri Jan 10, 2020 10:07 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7355
Location: SW Washington
Car Model*: 1954 Dodge C1-B8
1977 Pickup transmission options from the dealership data book: https://www.hamtramck-historical.com/de ... k-09.shtml

Attachment:
77_trucks_0017c.jpg
77_trucks_0017c.jpg [ 133.93 KiB | Viewed 330 times ]


From your field reports it appears that the A833OD availability expanded in later years.

_________________
Joshua


Top
   
PostPosted: Sat Jan 11, 2020 9:46 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 6950
Location: Vine Grove, KY
Car Model*: More than I should have...
I have one out of a later D150.

_________________
Rob

Drag Racing
Commentator/
Points Keeper

Image


Top
   
PostPosted: Sun Jan 12, 2020 1:07 am 
Offline
1 BBL (New)
User avatar

Joined: Thu Jul 09, 2015 11:19 pm
Posts: 5
Car Model*: 1984 dodge D150 slant6 single cab long be step-sid
For sale? :D


Top
   
PostPosted: Sun Jan 12, 2020 7:01 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 2862
Location: Indianapolis
Car Model*:
If Rob does not want to part with that long tail A833 I have one that is available.


Top
   
PostPosted: Sun Jan 19, 2020 2:38 pm 
Offline
TBI Slant 6
User avatar

Joined: Mon Aug 03, 2015 2:39 pm
Posts: 208
Location: Dallas Texas
Car Model*:
My '84 W100 had a /6, np435 with 130 tooth flywheel, 11 in clutch and high mount starter.

_________________
1976 Feather Duster /6 4sp
1984 W100 318 727 np241
1972 'Cuda 340 4sp
1985 D250 360 46RH


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 14 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited