Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum upgrade!
It is currently Fri Apr 10, 2020 11:39 am

All times are UTC-07:00




Post new topic  Reply to topic  [ 22 posts ]  Go to page Previous 1 2
Author Message
 Post subject: Re: Flywheel
PostPosted: Sun Mar 22, 2020 12:18 pm 
Offline
2 BBL ''SuperSix''
User avatar

Joined: Thu Jan 26, 2017 10:50 am
Posts: 20
Location: South Carolina
Car Model*: 1965 Dart
Will a 130 thooth flywheel fit in the 3743643-1aluminum bellhousing that I have?


Top
   
 Post subject: Re: Flywheel
PostPosted: Sun Mar 22, 2020 4:45 pm 
Offline
EFI Slant 6

Joined: Thu Jun 07, 2012 4:29 pm
Posts: 482
Location: Houston
Car Model*: 68 Valiant
viewtopic.php?f=20&t=48219


Top
   
 Post subject: Re: Flywheel
PostPosted: Mon Mar 23, 2020 8:53 am 
Offline
Turbo Slant 6
User avatar

Joined: Tue Nov 23, 2004 6:05 pm
Posts: 646
Location: Desoto Texas
Car Model*: 1972 Dodge Colt
Not sure about casting numbers, but here is a 130 tooth flywheel and a cut down stock 3 speed bellhousing.
You can see how the 130 flywheel hits.
Starter would not fit either due to increased diameter.


Attachments:
IMG_0106 s.JPG
IMG_0106 s.JPG [ 75.45 KiB | Viewed 444 times ]

_________________
Hyper_pak
Top
   
 Post subject: Re: Flywheel
PostPosted: Mon Mar 23, 2020 9:35 am 
Offline
Turbo Slant 6
User avatar

Joined: Tue Nov 23, 2004 6:05 pm
Posts: 646
Location: Desoto Texas
Car Model*: 1972 Dodge Colt
And did I say before, I hate photobucket.

_________________
Hyper_pak


Top
   
 Post subject: Re: Flywheel
PostPosted: Tue Mar 24, 2020 4:33 am 
Offline
2 BBL ''SuperSix''
User avatar

Joined: Thu Jan 26, 2017 10:50 am
Posts: 20
Location: South Carolina
Car Model*: 1965 Dart
Looks like I'm going to have to use the 122 tooth flywheel with bellhousing that I have. The ring gear is 12-3/8 across. So I checked the distance between center of bell to starter gear is 6 3/16.


Top
   
 Post subject: Re: Flywheel
PostPosted: Wed Mar 25, 2020 7:26 pm 
Offline
Supercharged
User avatar

Joined: Sat Nov 27, 2004 8:03 pm
Posts: 5544
Location: IRWIN PA
Car Model*:
hyper_pak wrote:
And did I say before, I hate photobucket.



Yeah me too. I have a lot of stuff on there that I should migrate or copy somewhere else. Sorry.



Gref

_________________
Greg Ondayko
69 Dart http://www.youtube.com/hyperpack
Image


Top
   
 Post subject: Re: Flywheel
PostPosted: Thu Mar 26, 2020 7:00 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9659
Location: Salem, OR
Car Model*:
So if you've been using the search function you will note that you get few choices...

Drill 122 Tooth Flywheel to use other make cover and disc.
Use an unavailable adaptor to allow the switch to a small block clutch. (May not fit in Pre-67 A-body without body mods).
Use an unavailable bellhousing to allow the use of the small block clutch. (Will need body massage to fit in Pre-67 A-body.)
Switch to an automatic...

I would prefer to see an inspection cover with a new conversion, as Hipo slants getting the clutch hammered on launch
tend to loosen the assembly fasteners... even with sheetmetal keepers on the flywheel bolts and red thread locker on the clutch
cover bolts you would still want to look over the fasteners after 100 miles, 500 miles, and/or a day of hard launches. The other
issue is that we have had members in the past that have had either the set screw for the hydro TOB collar loosen...or have
enough wear where the cylinder has excess runout and can leak... with access, it's easy to reset it, or see why you have a leak
(also good to inspect if the rear bearing seal wears and you get some nice crank case 10W-30 on your flywheel and clutch assembly
going up a nice hill...).


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 22 posts ]  Go to page Previous 1 2

All times are UTC-07:00


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited