Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Thu Mar 28, 2024 2:22 am

All times are UTC-07:00




Post new topic  Reply to topic  [ 31 posts ]  Go to page Previous 1 2 3 Next
Author Message
 Post subject:
PostPosted: Thu Feb 09, 2017 7:03 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
I see no reason to put a 727 behind a slant on a daily driver, even one that does a lot of towing or hauling. My 1976 Dodge truck has a 225/727 combination and I plan on swaping out the 727 for a 904. The earlier and lighter A100 truck or van chassis would do just fine with a 904. The slant six 904T actually has a four gear planetary gearset and the same number of clutches as V-8 transmissions.

And the factory adapter plate was dropped in 68 when Chrysler came out with the slant six case for the 727. The adapter is only found in 64-67 A100/A108 trucks and vans. The coolest combination of factory parts is a 225 with the adapter plate mating it to an A500 four speed auto with overdrive.


Top
   
 Post subject:
PostPosted: Mon Mar 06, 2017 3:05 pm 
Offline
1 BBL (New)

Joined: Wed Feb 08, 2017 8:05 pm
Posts: 3
Location: Surrey
Car Model:
Reed wrote:
I see no reason to put a 727 behind a slant on a daily driver, even one that does a lot of towing or hauling. My 1976 Dodge truck has a 225/727 combination and I plan on swaping out the 727 for a 904. The earlier and lighter A100 truck or van chassis would do just fine with a 904. The slant six 904T actually has a four gear planetary gearset and the same number of clutches as V-8 transmissions.

And the factory adapter plate was dropped in 68 when Chrysler came out with the slant six case for the 727. The adapter is only found in 64-67 A100/A108 trucks and vans. The coolest combination of factory parts is a 225 with the adapter plate mating it to an A500 four speed auto with overdrive.


It would become very apparent why you have install a 727 in a SWB A100. The transmission cannot exceed 22" in length. The only options for a short shaft are in the 727.

_________________
64 Dodge A100, 65 Dodge A100 Sportsman, 67 Dodge A100 Sportsman


Top
   
 Post subject:
PostPosted: Mon Mar 06, 2017 3:18 pm 
Offline
1 BBL (New)

Joined: Wed Feb 08, 2017 8:05 pm
Posts: 3
Location: Surrey
Car Model:
"The earlier and lighter A100 truck or van chassis would do just fine with a 904. The slant six 904T actually has a four gear planetary gearset and the same number of clutches as V-8 transmissions."

wow....again, the A100 truck/van chassis cannot fit the 904 due to drive shaft length limitations. ONLY the A108 van could put in the 904. All in the hopes to gain back a possible...what, 15% (maybe) power loss compared to a 727??? I'm sure the other model trucks in the line would have no issues with the extra 4" of tail shaft that the A100 does.

_________________
64 Dodge A100, 65 Dodge A100 Sportsman, 67 Dodge A100 Sportsman


Top
   
 Post subject: Correct...
PostPosted: Mon Mar 06, 2017 5:13 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9760
Location: Salem, OR
Car Model:
Quote:
It would become very apparent why you have install a 727 in a SWB A100. The transmission cannot exceed 22" in length. The only options for a short shaft are in the 727.


Oddly this issue is even noted in the old Carroll Shelby version of the Direct Connection Chassis Manual... LOL....

Although I had heard a rumor at one time that AMC's version of the 904 came with a slightly shorter tailshaft than the Mopar version (not sure if the mainshaft is compatible with the mopar yoke or guts....


Top
   
 Post subject:
PostPosted: Mon Mar 06, 2017 7:50 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
I stand corrected. Having never owned or worked on euther an A100 or an A108, I was not aware of the lack of space for a 904. However, I stand by my recommendation of a 904 over a 727, provided there is space for it.


Top
   
 Post subject:
PostPosted: Mon Mar 06, 2017 8:34 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Is the space a hump or driveshaft length problem?

If driveshaft length, I would think you could use high angularity u-joints or CV joints and have a short driveshaft.

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Mon Mar 06, 2017 10:02 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
I do know that a b series van transmission bracket can be adapted to the A series body.


Top
   
 Post subject: Transmission length
PostPosted: Mon May 29, 2017 12:37 am 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Thu Dec 22, 2005 11:04 pm
Posts: 36
Location: British Columbia
Car Model: 65 A100 truck
A full length 727 will fit an A100 with the 90 inch WB
I have a full length ( same as a 727 ) 833 OD in my 65 A100 pickup .
have owned 12 A100's and A108's . Not sure where Bionic is getting his info , I have pics if need be .


Top
   
PostPosted: Sun Jun 28, 2020 10:40 pm 
Offline
3 Deuce Weber

Joined: Sun Jun 05, 2016 12:18 pm
Posts: 72
Location: San Diego Ca
Car Model: 1965 Dodge A100 Pickup w/Super Six
Is your 833 in your A100 a four speed plus overdrive? Or is fourth gear OD? Also, column shift?


Top
   
PostPosted: Mon Jun 29, 2020 2:27 pm 
Offline
Turbo Slant 6

Joined: Thu Jun 07, 2012 4:29 pm
Posts: 737
Location: Houston
Car Model: 68 Valiant
A 904 might have the same number of clutches and planetary gears as a 727, but they are way smaller diameter. There is a relationship fully understood only by the highly educated, and Keaneu Reeves, which speaks to the fact that clutch holding strength goes up exponentially with diameter.

Now, who wanted the short 727....?


Attachments:
RenoCF4.JPG
RenoCF4.JPG [ 59.41 KiB | Viewed 4695 times ]
Top
   
PostPosted: Tue Jun 30, 2020 8:08 am 
Offline
4 BBL ''Hyper-Pak''

Joined: Mon Apr 04, 2005 5:28 pm
Posts: 43
Location: Vernon,WI
Car Model: 1966 Plymouth Valiant
keep in mind the a100/108 trans mount is on the Top. unless you are making a crossmember or a custom mount bracket ( some have bolted to the tail housing bolts ) a standard car trans wont work.


Top
   
PostPosted: Tue Jun 30, 2020 2:10 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
GregCon wrote:
A 904 might have the same number of clutches and planetary gears as a 727, but they are way smaller diameter. There is a relationship fully understood only by the highly educated, and Keaneu Reeves, which speaks to the fact that clutch holding strength goes up exponentially with diameter.

Now, who wanted the short 727....?


But is the added clutch holding strength (a) necessary and (b) worth the tradeoff in overall drivetrain efficiency over a 904? I stand by my assertion that in most applications there is no reason to put a 727 behind a slant six.


Top
   
PostPosted: Tue Jun 30, 2020 2:42 pm 
Offline
Turbo Slant 6

Joined: Thu Jun 07, 2012 4:29 pm
Posts: 737
Location: Houston
Car Model: 68 Valiant
I agree, the 727 is overkill x 5 for the average Slant.


Top
   
PostPosted: Wed Jul 01, 2020 8:45 am 
Offline
EFI Slant 6
User avatar

Joined: Thu Jul 24, 2003 4:51 pm
Posts: 465
Car Model:
Reed wrote:
I stand by my assertion that in most applications there is no reason to put a 727 behind a slant six.


Well there obviously is, otherwise Mopar wouldn't have done it now would they???


Top
   
PostPosted: Wed Jul 01, 2020 9:22 am 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
69a100 wrote:
Reed wrote:
I stand by my assertion that in most applications there is no reason to put a 727 behind a slant six.


Well there obviously is, otherwise Mopar wouldn't have done it now would they???


Yes, but the reason most likely wasn't because of concerns for longevity or technical necessity. My 1976 D100 was built with a 225 and a 727. But that was because Dodge did not offer 904s in any trucks or vans that year, no matter the engine or package ordered. Just a few years later in the early 80s Chrysler was putting 904s and 999s behind smallblock engines in trucks and vans without any significant changes in the design of the engines or transmissions.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 31 posts ]  Go to page Previous 1 2 3 Next

All times are UTC-07:00


Who is online

Users browsing this forum: No registered users and 45 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited