Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Thu Mar 28, 2024 10:22 pm

All times are UTC-07:00




Post new topic  Reply to topic  [ 250 posts ]  Go to page 1 2 3 4 517 Next
Author Message
 Post subject: 83 D-150 Project
PostPosted: Wed Aug 03, 2011 4:30 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3805
Location: Indianapolis
Car Model:
here are photos of the D-150 as it is today

http://www.flickr.com/photos/13718356@N ... 350283928/

block,head, crank & rods are at Ed'd Machine shop in Morresville, Cylinders are rough bored, awaiting the pistons for the measure and hone.
OS valves are in the head, crank is polished,,,

tomorrow the tranny will get dropped off at Brewers at Ludlow Falls OH for an internal check-up. Got lucky on the delivery and return ,, the wife's family is from Greeville OH,, about 20 minutes from Brewer's, wife will drop it off tomorrow on the way to visit her mom.

interior is about stripped, took out the rear window today. This weekend plan to remove the remaining wiring, lights, rear bumper...

Then it will be ready to drag it over to Kenny's shop,,, will delay a bit on that as I am wanting the weather to break a bit before getting into the paint and body work.
So I may start on doing the brakes and re building the front end.

regards
DT


Top
   
 Post subject:
PostPosted: Sun Aug 21, 2011 5:48 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3805
Location: Indianapolis
Car Model:
got the head back from the machine shop and worked with it today

1) made a construction paper duplicate of the head intake and exhaust face, and set that on the intake manifold, to see how the intake port opening align,,actually really close, looks like the out board intake runners are pulled in towards the center just a bit,, maybe a 1/32,, a little grinding will make those match better.
2) did not work to enlarge the head port runners, but went over them to smooth just a bit.
3) worked in the valve pocket to blend the transition to the larger seats, took the step off the back on the valve guide boss, made it a large filet.
4) spent some time narrowing the intake short side radius,,to check my work I pressed a short length of solder wire from the valve seat across the floor to the port opening,, when the radius transition looked smooth I traced that on paper and used that as a model to get them all about the same,,

here are some photos
http://www.flickr.com/photos/13718356@N ... 488071408/


regards
DT


Top
   
 Post subject:
PostPosted: Sun Aug 21, 2011 10:12 pm 
Offline
TBI Slant 6
User avatar

Joined: Sat Feb 21, 2009 8:59 pm
Posts: 225
Location: Indy
Car Model:
Looking very nice.


Top
   
 Post subject:
PostPosted: Mon Aug 22, 2011 12:55 pm 
Offline
Poser
User avatar

Joined: Thu Nov 29, 2007 3:18 pm
Posts: 3121
Location: Indy
Car Model:
Coming right along! :D

_________________
66 Lil' Red Piggie Valiant (Mater Crusher) - Thanks Zilla!!!!! 72 Demon (Number 1 Son's)


Top
   
 Post subject:
PostPosted: Mon Aug 22, 2011 1:25 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
Looking good.


Top
   
 Post subject:
PostPosted: Mon Aug 22, 2011 3:23 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3805
Location: Indianapolis
Car Model:
want to see "looking good", should have seen me after that little bit of porting work,,looked like a re run of the days when I was a laborer in the IH foundry cleaning room. I did wear a respirator,,,,


Top
   
 Post subject:
PostPosted: Mon Aug 22, 2011 3:44 pm 
Offline
Poser
User avatar

Joined: Thu Nov 29, 2007 3:18 pm
Posts: 3121
Location: Indy
Car Model:
Where are the pics of that? :lol:

_________________
66 Lil' Red Piggie Valiant (Mater Crusher) - Thanks Zilla!!!!! 72 Demon (Number 1 Son's)


Top
   
 Post subject:
PostPosted: Thu Oct 27, 2011 9:35 am 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3805
Location: Indianapolis
Car Model:
got the tranny back from Brewers
new input / out bearings, syncros, seals, lever mounting studs,
had them go through the shifter to

looks like new

http://www.flickr.com/photos/13718356@N ... 990853720/

and got the time penciled in at Kenny Johnson's body shop,, rolling chassy goes in the second week of Nov.
He said he would have it about a month, would be fun to get it back for Christmas!


Top
   
 Post subject:
PostPosted: Thu Oct 27, 2011 12:45 pm 
Offline
EFI Slant 6

Joined: Thu Jun 24, 2010 12:30 pm
Posts: 304
Location: GYMPIE,QLD,AUSTRALIA
Car Model:
Sweet. 8)

_________________
Image
DRIVE IT,DON'T HIDE IT


Top
   
 Post subject:
PostPosted: Thu Oct 27, 2011 3:44 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Jun 19, 2004 8:01 pm
Posts: 1937
Location: Rhine, GA
Car Model:
Nice truck, is yours a "Miser" also? I'm guessing not since it has the third brake light/cargo light on the back of the cab.

_________________
82 D150-225/727
02 Dakota-3.9/5 speed
87 GMC C7000-8.2 Detroit Diesel/5+2


Top
   
 Post subject:
PostPosted: Thu Oct 27, 2011 6:06 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3805
Location: Indianapolis
Car Model:
The 83 D-150 is a very basic truck, slant, a 833, short bed, manual steer, looks like when Dad picked it out he did get the side stripes and a 2bbl,,,, has a 3:21 rear axel, has carpet on the floor and a sliding back glass, not tinted, the cab vent package is the bottom end one, defrost-heat and the infamous ram-vents

the third brake light is one of the additions that I am putting on the D-150, that is not factory

I have heard of the Miser package, what does that consist of?


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2011 7:30 am 
Offline
Turbo EFI
User avatar

Joined: Sat Jun 19, 2004 8:01 pm
Posts: 1937
Location: Rhine, GA
Car Model:
The miser package was a lack of options package. Yours sounds like it might be one also.

Old Miser ad: http://store.vintagepaperads.com/servle ... ser/Detail

_________________
82 D150-225/727

02 Dakota-3.9/5 speed

87 GMC C7000-8.2 Detroit Diesel/5+2


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2011 9:00 am 
Offline
TBI Slant 6
User avatar

Joined: Sat Feb 21, 2009 8:59 pm
Posts: 225
Location: Indy
Car Model:
Mine is the miser package.Option of 904 with lockup converter.Heavy duty front bearings though.


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2011 10:55 am 
Offline
TBI Slant 6
User avatar

Joined: Tue Dec 04, 2007 8:57 pm
Posts: 151
Location: Newport, Ohio
Car Model:
those were the days

a new truck for less than 6$K


thanks for sharing


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2011 11:12 am 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13008
Location: Fircrest, WA
Car Model: 76 D100
I have a hard time seeing what body work your truck needs. Very nice truck. Almost makes me want to get one.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 250 posts ]  Go to page 1 2 3 4 517 Next

All times are UTC-07:00


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited