Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Mar 29, 2024 3:04 am

All times are UTC-07:00




Post new topic  Reply to topic  [ 39 posts ]  Go to page 1 2 3 Next
Author Message
PostPosted: Tue May 22, 2018 10:15 pm 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
Cassi's original build featured a slant 6, but when she came back to me I decided (in my typical insane fashion) to remotor'er with something no one else'd done yet. I came up with the idea for a slant 8 after getting a Buick straight 8 in a parts swap. :twisted: The rest, as "they" say, will be recorded here ........

In that the only slush pump I like is the push button 904, and due to a loss of foot room thanks to the Buick's length I opted for two pedals, and so mated a pb904 to the '40 Buick 248 I'd gotten. I turned a flex plate adapter easily enough, but the bell adapter had to be 1.5" thick. So I bought a piece of plate, and had at it with my O/A set, grinders, drill press, and a few hand files. Four days later I bolted it all up for its initial assembling. Only took a couple hours to finesse it in, and top it off with a mini starter. 8)

This drive train required substantial changes to the tunnel, which I then set about. I also added a couple useful access hatches to it, for the trans adjustments and the rear trans mount and forward U-joint. At eleven pieces, it turned out to be the most pieces I've ever put into a tunnel. Still needs some finishing around the firewall.

The rest of the fitting in was fairly "straight" ( :lol: ) forward, with the exception of a unique motor mount being needed off the top of the trans adapter plate, at the firewall. The gas pedal had to go from a floor pivot style to a hanging spoon as well.

Carbs will be four 1.250" SUs that I'm cannibalizing from a set of six from another parts swap. The manifold plates I bought online, and the carb plates I cobbled. The tubes're just some EMT I had on hand, and the balance pipes're just hose (obviously :roll: ).

That's where she's at for now. This (re)project'll take a while, as I can only spare time to work on'er when the garage is clear of other projects. However, I do manage to get in a day or two a couple times a month, so sooner or later she will hit the street. Steady on, and all that. :D

Here's the link to her present Flickr set, and a couple pictures for here as well.

Image

Image

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Top
   
PostPosted: Wed May 23, 2018 5:40 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 16451
Location: Blacksburg, VA
Car Model:
Thanks for the inline rundown, Dick. Looks like an uber cool re-project. Dare to be stoopid.

Lou

_________________
Home of Slant6-powered fun machines


Top
   
PostPosted: Wed May 23, 2018 6:17 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8700
Location: Cox’s Creek, KY
Car Model: More cars than sense...
Uber Cool! 8)

_________________
Rob

I’m Mater
The Kentucky Poser

Image


Top
   
PostPosted: Wed May 23, 2018 8:47 am 
Offline
Board Sponsor & SL6 Racer
User avatar

Joined: Fri Nov 08, 2002 4:48 pm
Posts: 5835
Location: Burton BC canada
Car Model:
Its always nice to see what a "Builder" can do.....Salute!

_________________
Yeah....Im the one who destroyed this rare, vintage automobile.....

Image


Top
   
PostPosted: Wed May 23, 2018 6:34 pm 
Offline
4 BBL ''Hyper-Pak''

Joined: Mon Nov 10, 2014 3:43 am
Posts: 29
Location: arkansas
Car Model:
That's cool How does the steering work?


Top
   
PostPosted: Sun Jun 10, 2018 12:15 am 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
Regular track roadster style drag link.

Honesty requires me to admit that I forgot to reverse the gear in the box the first time I pasted it together, way back when. :oops:

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Top
   
PostPosted: Mon Jun 11, 2018 7:17 am 
Offline
Supercharged
User avatar

Joined: Sat Feb 16, 2008 1:25 pm
Posts: 5599
Location: Downeast Maine
Car Model:
Love the idea of a laid over straight 8.

Did you "cattywampus" the oil pan to take into account the lean?

Back in the day as a kid I loved the sound of a Buick Straight 8 in front of a slush box. We had an automatic 1954 Chieftain 8 that made about the same song; it replaced a 1952 Plymouth. That thing is going to sound sweet.

_________________
67' Dart GT Convertible; the old Chrysler Corp.
82' LeBaron Convertible; the new Chrysler Corp
07' 300 C AWD; Now by Fiat, the old new Chrysler LLC

Image


Top
   
PostPosted: Tue Jul 24, 2018 1:25 am 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
Not yet, the oil pan & pick-up mods'll be later when I go through the engine.

Got in a few more play days, so did a bit more on the throttle linkage. Also got the rear brakes & parking brake functional (fronts need new drums yet), fuel system complete from tank through pump, and roll bar added.

Then rolled'er up to the HAMBster's trailer so I could bring the HAMBster down to go through the bottom end. Musical Cars is pretty much the name of the game when you hobby out of a 1918 one car garage. :lol:

Image

Image

Image

Image

Image

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Last edited by Old6rodder on Fri Apr 12, 2019 4:24 pm, edited 1 time in total.

Top
   
PostPosted: Tue Jul 24, 2018 3:37 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 16451
Location: Blacksburg, VA
Car Model:
Very inspiring, Dick. Uber cool project, as usual.

Lou

_________________
Home of Slant6-powered fun machines


Top
   
PostPosted: Tue Jul 24, 2018 5:54 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8700
Location: Cox’s Creek, KY
Car Model: More cars than sense...
Lovin' it!!

So, are you keeping the Brick too?

_________________
Rob

I’m Mater
The Kentucky Poser

Image


Top
   
PostPosted: Tue Jul 24, 2018 10:36 am 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
The 'Brick'll stay with me at least 'til Cassi runs. Considering converting'er into a trailer for Cassi at some point, should she not sell.

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Top
   
PostPosted: Tue Jul 24, 2018 12:21 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8700
Location: Cox’s Creek, KY
Car Model: More cars than sense...
Can't you use the trailer you have now for Cassi? :? It would be a shame to take the Brick apart to make a trailer! :shock:

Or do you mean converting the Brick into a trailer to tow BEHIND Cassi..? Either way, please don't take the Brick apart!!

_________________
Rob

I’m Mater
The Kentucky Poser

Image


Top
   
PostPosted: Tue Jul 24, 2018 5:07 pm 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
Yes, option #2. 8)

If the 'Brick doesn't sell when I decide to put'er on the market I'll make a trailer for behind Cassi out of'er. In that Cassi has no stowage to speak of, I'll need to cobble up some sort of small trailer for trips & such. The 'Brick's tub'd make a fun one, should I wind up stuck with'er.

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Top
   
PostPosted: Fri Apr 19, 2019 8:24 pm 
Offline
Turbo Slant 6
User avatar

Joined: Wed Apr 30, 2003 6:43 pm
Posts: 976
Location: SoCal
Car Model: Toad Wagon
Been back in the garage a bit now & then since the parade. Nowhere near as much time as I'd like, but better'n nothing.

Ordered a bunch of SU bits & pieces from Burlen, just enough to get four of the carbs up to operating status. Wanted to get the linkage parts from'em as well, but couldn't handle their prices.
Sooooo ..... started the cobble, first four levers're now on the common shaft. Linkage now complete to that point. Four more, for the butterfly shafts, up next, then the drag links & springs. "Enrichment" linkage to follow.

Image

Image

Also butchered up a couple slant rocker boxes to try out a cosmetic "cap" for the Buick one. Think I'm starting to like the idea after all. If it turns out decent enough I just might use it. Just another of my hairball notions. :roll:

Image

The port side of the Buick block's somewhat similar in casting design to the aluminum slant, so that helps the visual aspect of the concept along a bit as well. You can see it fairly well in a couple of the engine placement pics in Cassi II's Flickr album here.

_________________
Sex, drags, and rock & roll.
Dick, 225% crazy.
Hobby (cars, that is) Photos link


Last edited by Old6rodder on Fri May 17, 2019 8:46 am, edited 1 time in total.

Top
   
PostPosted: Sat Apr 20, 2019 4:17 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 16451
Location: Blacksburg, VA
Car Model:
Thanks for sharing, Dick. Can't wait to go for a ride with you...

Lou

_________________
Home of Slant6-powered fun machines


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 39 posts ]  Go to page 1 2 3 Next

All times are UTC-07:00


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited