Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 30, 2024 4:05 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Thu Oct 27, 2005 9:41 pm 
Offline
Turbo EFI
User avatar

Joined: Sun Nov 03, 2002 1:49 pm
Posts: 2445
Location: Lubbock, TX
Car Model:
For future reference: Is it possible and has anybody done a main/connecting rod bearing change with the engine still in the car? The reason I ask:

I still have good compression on all cylinders (150psi to 143psi) on the cylinders, but I can hear a very slight knock(s) at idle and a little above. Also, oil pressure drops down to 45psi after driving for 20 miles or so at freeway speeds (60-70mph).

If I remove the center steering link, it looks like there is plenty of room to work under there, especially after lifting the engine up a couple of inches. Would be a good time to change the rear seal also. Any constructive ideas? Thanks.


Top
   
 Post subject: Once a long time ago...
PostPosted: Thu Oct 27, 2005 9:47 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
I've never seen a main bearing change done that way, but I helped my grandfather replace a con. rod bearing in my uncle's 318 that way...
(jack up motor, pull pan, rotate crank, pull cap, push rod up pull bearings, inspect crank surface, install new bearing, put on some goop, put it back together).
Of course that's a barnyard repair, just to get my uncle by for a little while longer...I'd be more worried now, about clearances...

I'm sure pulling the crank under the car would be fun, sorta like doing a tranny swap...

-D.Idiot


Top
   
 Post subject:
PostPosted: Thu Oct 27, 2005 10:02 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Jul 08, 2003 11:33 am
Posts: 2378
Location: Central GA
Car Model: Many & varied, including stock & hopped up /6's
Been there, done that... Search archives. You probably don't need to, though... Your oil pressure seems fine to me, the slight knock could be anything, including the fuel pump or a piston pin, neither of which would warrant a bearing change. There are many non-life-threatening things that can cause a subtle knock on a motor with some miles.

D/W

_________________
Image
If it ain't broke, fix it!


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2005 3:24 am 
Offline
Supercharged
User avatar

Joined: Mon Sep 26, 2005 5:09 pm
Posts: 2946
Location: Gilbert, Arizona
Car Model: 1962 Plymouth Valiant Signet
In addition to the above, you could actually make the knock worse. Changing the bearings will slightly change the position of the pistons in the bore leading to the possibility that the top ring of one or more pistons will strike the wear ridge at the top of the cylinder bore. This, of course, will cause an annoying knock and can lead to broken rings as well. 45 psi oil pressure is more than adequate and does not indicate bearing problems. You should determine exactly what the noise is before trying to repair it.

_________________
David Kight
'62 Valiant Signet, White
'98 Dodge Dakota
'06 Jeep Liberty

Growing older is unavoidable but growing up is strictly optional.


Top
   
 Post subject:
PostPosted: Fri Oct 28, 2005 6:38 am 
Offline
Turbo Slant 6

Joined: Sat Feb 19, 2005 5:31 am
Posts: 969
Location: Norway
Car Model:
But you can, if you want to


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 5 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Ahrefs [Bot], Bing [Bot] and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited