Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 6:43 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 69 posts ]  Go to page Previous 1 2 3 4 5 Next
Author Message
 Post subject:
PostPosted: Fri Nov 11, 2005 7:40 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
OK, perhaps, it looks like the company has still not improved its corporate responsibility position though, which is neither here nor there, I just picked up a BlueStreak coil and an AL111 condenser, let's see what happens. Stay tuned...

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 8:53 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
No improvement. New coil, new standard points, new blue streak condenser, no change. I do not have a spare carburetor and as such I cannot eliminate it as a possible cause, but the more I think about it, the more it seems like I have a head crack. After the engine loses power, the idle vacuum drops, and slowly recovers over five seconds with no change in the idle quality and speed, and since I adjusted my valves, I have run the same circuit over and over, and the stumble begins ALWAYS in the same place, within 150 feet, you can almost set your watch to it. The car loses power, stalls, it will recover if you give it gas but still surges and limps all the way home unless I allow it to idle a little, then you can get on it again for a few seconds. Until that point, the car runs great. I am very close to deciding to remove my cylinder head and send it out for magnafluxing. but as soon as I do that, the engine is dead until I find another head.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 9:28 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
I just looked at the Kem instruction kit, it does not specifically mention "power valve" but it does show the economiser diaphragm, the triangular housing on top of the fuel bowl; on a hunch I removed the diaphragm and looked at it, everything looks fine, no cracks or folds. I blew out the vacuum passage and it is clear.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 10:21 am 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
OK, perhaps, it looks like the company has still not improved its corporate responsibility position though
I can't think of any oil companies who are fuzzy and lovable. :-(

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 10:23 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
you are right about that.

I am going to go up the mountain and grab some fatter jets, I cant think of anything else aside from a new carb and/or head.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 10:32 am 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
65 is already very big. You don't need a bigger jet.

And I don't think you need a new head, either.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 11:34 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
well, here's what happened. I went out on a limb and grabbed a big fat #70 jet and threw it on, then went out on a test drive. Car is still showing the same symptoms, only this time the stumble came back much sooner, about half the distance I was seeing before. Once I got it home I ran it in gear at WOT until it stumbled and stalled. I removed the economiser cover and diaphragm, and looked in the hole. Well the fuel level is right at the pivot point for the economiser relay lever, that plastic jiggie clipped onto the side of the metering block. That's pretty far down, Id say. I could only push the float down about 1/8" before it hit the bottom. So either my float setting is still too low, or we have a problem with the fuel supply, but the pump is new and the pressure is constant. And get this, the exhaust is blowing clean out the tailpipe, even while it's stumbling. No strong exhaust smell either.

I think Ill pull the carb off and try to set that float a little more carefully...

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 11:59 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
OK, float setting was at spec, actually the relay lever hinge point is higher up than it looked with that fuel in there. I did raise it a touch.

At any rate this car isnt going anywhere any time soon. Ive done all the easy things. I hoped that in a rush I could throw stuff at it and get the problem to go away, but whatever is wrong with this car isnt going to come off some shelf in Hamilton. Oh well, Ive got all weekend now to sort this out, and Ive got a bunch of good leftover parts that by rights I really should have had onhand for emergencies, anyway. I really wish I could see what my mixture and cylinder pressure was doing when it acts up, but that's not going to happen...

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:03 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Quote:
well, here's what happened. I went out on a limb and grabbed a big fat #70 jet and threw it on, then went out on a test drive. Car is still showing the same symptoms, only this time the stumble came back much sooner, about half the distance I was seeing before. .

Well you went richer and it happened sooner...........

I'd try going leaner........

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:05 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
What kinda float does the carb have??????

A bad float could sink and let too much fuel in.


The brass ones spring leaks, the plastic ones will actually absorb gas and sink..............

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:13 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
The brass ones spring leaks
There are no brass Holley 1920 floats.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:15 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Quote:
There are no brass Holley 1920 floats.

I've got a BBS, so I don't know..............


But I've had the absorb the gas problem with a Quadrajet..............

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:26 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
After a few decades' service, those Holley 1920 metering blocks just die, and nothing you can do will bring them back from the dead.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:30 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
it's definitely still buoyant, but thanks for the thought. Im running short on them right now.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 2:33 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
So youre saying if I track down an unused metering block, i can buy myself another 20 years? :lol: wouldnt that be sweet.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 69 posts ]  Go to page Previous 1 2 3 4 5 Next

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited