Slant Six Forum
https://slantsix.org/forum/

Offenhauser group buy?
https://slantsix.org/forum/viewtopic.php?t=30815		 Page 8 of 9
Author:  66Dart [ Thu Sep 11, 2008 10:40 am ]
Post subject:  Offy Cover w/ PCV
Here's my cover with the pcv installation components per slant six dan's article regarding retrofit recommendations.
Image
Image

Works Great

66Dart
Author:  wvenable [ Thu Sep 11, 2008 1:13 pm ]
Post subject: 
66 Dart, thanks for the post! Nice clean install!
Author:  SlantSixDan [ Thu Sep 11, 2008 3:56 pm ]
Post subject: 
It is a nice installation, but I can't figure out what you are using for the grommet that holds the PCV valve into the new breather cap. It's not a standard Chrysler PCV valve grommet, though it looks like you are using a '61-'69 metal "curved pipe" Chrysler PCV valve.
Author:  SlantSixDan [ Thu Sep 11, 2008 3:58 pm ]
Post subject: 
Quote:
Is there a thread with a complete list of items to buy for a baffle and a PCV?
Here y'go.
Author:  Guest [ Thu Sep 11, 2008 4:17 pm ]
Post subject: 
Quote:
Is there a thread with a complete list of items to buy for a baffle and a PCV? Possibly pics also of the installation and stuff?
Here's how to get the 2 grommets.
Author:  Hyper72Valiant [ Fri Sep 12, 2008 12:17 am ]
Post subject: 
Sweeeet, thanks guys! Good pics too by the way and nice car.
Author:  lowbudget [ Fri Sep 12, 2008 3:44 am ]
Post subject: 
All the parts were $7.17 thru Rock auto. That and 20 NGK plugs cost me 10.00 to ship. I needed plugs as Snowmobile season is coming. The shipping is worth it considering someone might see you ordering Chevy parts :oops: at your local parts store.
Author:  ChazRam [ Sat Sep 13, 2008 3:37 pm ]
Post subject:  Schweeeeet!!!!!
I recant everything I said about the valve cover. Thanks to SlantSixDan and 66Dart for not only all the info needed but pics to boot. Since this can be done without mods to the valve cover other that drilling a one inch hole I am in the mix for one. Please update with the info etc. SOON!!!
Chas. :D
Author:  Jester [ Sat Sep 13, 2008 7:56 pm ]
Post subject: 
count me in for the valve cover (depending on shipping cost to Canada), but not for the intake. Maybe a seperate group buy can be done for that?

I just don't know which intake I want yet :)
Author:  SlantSixDan [ Fri Sep 26, 2008 8:00 am ]
Post subject: 
Please use this thread for discussing the valve covers and intakes themselves. To participate in the group buy, please go here. --mod
Author:  pharmboy [ Fri Oct 03, 2008 5:49 am ]
Post subject: 
Well, it looks like the rain has finally stopped, so tonight I'm gonna start working on my offy valve cover. It's already drilled for a PCV valve, but I'm gonna open it up to take an oil separator, and fit it with a better oil cap(Mr Gasket's chrome 710 cap), it's a push-in, so it'll be a matter of making the hole in the valve cover smaller on that side (hooray for mighty putty...don't laugh, I swiped a stick from my dad while I was home last weekend), and getting it cleaned up and painted. I'll take pictures, wish me luck
Author:  lowbudget [ Wed Dec 03, 2008 9:18 am ]
Post subject: 
Since the valve covers are here what is everyone using for a oil fill/breather cap? I saw some clamp on ones at Summit but haven't found the push in one. Thanks Mike
Author:  lowbudget [ Thu Mar 12, 2009 3:23 pm ]
Post subject: 
Here is mine ready for installation. I wrinkled blacked it. It came out so so. Image[/img]
Author:  62Signet [ Thu Mar 12, 2009 3:36 pm ]
Post subject: 
What would you say needs replacing if you get traces of oil pooling in the fin grooves?
Author:  SlantSixDan [ Thu Mar 12, 2009 4:12 pm ]
Post subject: 
That suggests you haven't got your crankcase ventilation set up correctly. How's yours set up? You've got an oil cap on the chimney at the front of the cover and...?
Page 8 of 9 All times are UTC-08:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/