Slant Six Forum
https://slantsix.org/forum/

Slant 6 turbo project
https://slantsix.org/forum/viewtopic.php?t=54579		 Page 10 of 10
Author:  Dart270 [ Thu Mar 19, 2020 3:44 am ]
Post subject:  Re: Slant 6 turbo project
I am running 14 psi (max) on my 68 Dart and it works very well and is reliable. Usually I run 11 psi on the street, which still plenty of power.

Enjoy the drive,

Lou
Author:  Thomas S [ Fri Mar 20, 2020 1:16 pm ]
Post subject:  Re: Slant 6 turbo project
Image
Slant 225 coming from a Belvedere 63. A guy did an engine swap to v8.
Now this is resting in my garage . good spare engine..

Image
I am doing a new trigger bracket, the old one was very close to the electric fan..
Thomas
Author:  Thomas S [ Sun Mar 22, 2020 1:23 pm ]
Post subject:  Re: Slant 6 turbo project
Trigger bracket soon finish.
Image

Just need to adjust the lash between sensor / trigger.
The old bracket was adjustable sideways, in case you pull the harmonic balancer and cant line it up when put back
Al the best Thomas
Image
Author:  Greg Ondayko [ Sun Mar 22, 2020 3:32 pm ]
Post subject:  Re: Slant 6 turbo project
Will you be machining the dampener so that it doubles as the trigger wheel?

Greg
Author:  Thomas S [ Sun Mar 22, 2020 5:00 pm ]
Post subject:  Re: Slant 6 turbo project
Hello Greg,
Sorry can you explain a bit more..
"machining the damper so that ..etc :?:
Author:  Greg Ondayko [ Sun Mar 22, 2020 5:09 pm ]
Post subject:  Re: Slant 6 turbo project
Nevermind.

I see in the second picture that you have a trigger wheel bolted in front of the damper.

Thanks,

Greg
Author:  Thomas S [ Sat Feb 06, 2021 11:47 am ]
Post subject:  Re: Slant 6 turbo project
Hello,
Some new stuff..
A 3 way fuel tap, so you can choose to use ordinary or a small fuel tank in the trunk.
And its regulated from the trunk
Can bee good to run an e85 car on ordinary pump gas now and then to clean the injectors ,runners and other Components
Just one more thing to do , hang Up the fuel hose properly some places
Its -5 Celsius , 23 farensomething.. and i am working outside..

Image
Author:  Thomas S [ Sat Feb 06, 2021 12:05 pm ]
Post subject:  Re: Slant 6 turbo project
Trunk
[url][url=https://www.bildtagg.se/bild/xfjlppfg4x63hxged1snrfg]Image[/url][/url]
Author:  Greg Ondayko [ Sat Feb 06, 2021 4:21 pm ]
Post subject:  Re: Slant 6 turbo project
Nice work,


Soon the frost and snow will be gone and it will be up to a Balmy 15° outside.


Greg
Author:  Thomas S [ Sun Feb 07, 2021 7:51 am ]
Post subject:  Re: Slant 6 turbo project
Thanks Greg,
Yes the spring can be around the corner..

Fuel tap access from the trunk
[Image]
Author:  Thomas S [ Tue Feb 16, 2021 5:24 am ]
Post subject:  Re: Slant 6 turbo project
I found an quite nice gearing calculator.
https://www.blocklayer.com/rpm-gear.aspx
Set your gear ratio,tire size etc.
And this turns up
A lot of info to get, how different gearing and tire size affecting rpm and speed

[url=https://www.bildtagg.se/bild/s8v44 ... 15om[/img][/url]

Also this page was very interesting
Learning curves a race friendly dyno graph
https://dsportmag.com/the-tech/learning ... yno-graph/
Page 10 of 10 All times are UTC-07:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/