| Slant Six Forum https://slantsix.org/forum/ |
|
| Hyper Pak https://slantsix.org/forum/viewtopic.php?t=49388 |
Page 2 of 2 |
| Author: | Dart270 [ Tue Jul 24, 2012 5:54 am ] |
| Post subject: | |
Not original hpak exhaust. Most likely 1980s-up Mopar 6 into 1 headers. If the rust is mostly surface, and the engine starts and runs with no smoke, maybe the car is worth $1500-3k? Really hard to tell from those -pics. Lou |
|
| Author: | 75slant6 [ Tue Jul 24, 2012 6:57 am ] |
| Post subject: | |
So either way it's pry not worth 5k? That's his asking price |
|
| Author: | Dart270 [ Tue Jul 24, 2012 7:50 am ] |
| Post subject: | |
If it runs and drives clean, stops well, and runs 16s in the 1/4, then $5k is OK. Otherwise, he is full of smoke. Lou |
|
| Author: | 75slant6 [ Tue Jul 24, 2012 7:53 am ] |
| Post subject: | |
About what does a completely stock 225 in an abody run in a 1/4? |
|
| Author: | Joshie225 [ Tue Jul 24, 2012 7:56 am ] |
| Post subject: | |
If that's the carburetor linkage in the last picture it's not the Hyper-Pak intake manifold, but something shorter like an Offy. |
|
| Author: | 75slant6 [ Tue Jul 24, 2012 8:03 am ] |
| Post subject: | |
Well, I just talked to the guy n he might send me some more pics, and y'all were right, it has a steel tube 6-1 header |
|
| Author: | 63Dart170 [ Tue Jul 24, 2012 3:21 pm ] |
| Post subject: | |
Quote: So either way it's pry not worth 5k? That's his asking price
I wouldn't give him over $1,000 for that - there's a ton of work to be done to make it presentable, even if it does have the more rare aluminum block.
|
|
| Author: | 75slant6 [ Tue Jul 24, 2012 4:56 pm ] |
| Post subject: | |
Hmm.. I thought they were worth a lot more than that! |
|
| Author: | DusterIdiot [ Tue Jul 24, 2012 5:03 pm ] |
| Post subject: | Slow and Slower... |
Quote: About what does a completely stock 225 in an abody run in a 1/4?
With highway gears and stock everything, about 19-22 depending on year and other factors. With some minor improvements noted here for "gas mileage" you can go into the 18's....With much more involved improvements still with stock hardware...about 17 is the limit...I can find a better looking road toad for $5-800 in Oregon, I'd say the cost of the intake manifold and headers would be worth $500-600 depending on several factors...aluminum block...unless specifically collecting them, or you know it's in really good shape...it's worth scrap. -D.Idiot |
|
| Author: | SlantSixDan [ Tue Jul 24, 2012 5:54 pm ] |
| Post subject: | |
Um. The body of that car is about as "solid" as a politician's promise. Rusty steel tube headers: NOT Hyper-Pak equipment. Common short 4bbl intake (I think I may detect the Offenhauser "O" logo, unless my eyes deceive me): NOT Hyper-Pak equipment. $5K? No. |
|
| Author: | zorg [ Tue Jul 24, 2012 6:34 pm ] |
| Post subject: | |
Quote: I wouldn't give him over $1,000 for that - there's a ton of work to be done to make it presentable.
It all depends upon what you're looking for. Personally, I wouldn't touch the body, but build a screaming H-pac motor for it and surprise some people. $5k is quite steep, though!
|
|
| Author: | 75slant6 [ Tue Jul 24, 2012 7:04 pm ] |
| Post subject: | |
Ok. I'm not a big fan of the body style but I'd LOVE to have some original hyper Pak stuff!! |
|
| Author: | 75slant6 [ Tue Jul 24, 2012 7:05 pm ] |
| Post subject: | |
Thanks lot for all the imput guys!! |
|
| Page 2 of 2 | All times are UTC-07:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|