| Slant Six Forum https://slantsix.org/forum/ |
|
| Volare project https://slantsix.org/forum/viewtopic.php?t=68082 |
Page 2 of 2 |
| Author: | Wesola78 [ Thu Mar 13, 2025 1:17 pm ] |
| Post subject: | Re: Volare project |
I edited it. |
|
| Author: | slantzilla [ Thu Mar 13, 2025 2:07 pm ] |
| Post subject: | Re: Volare project |
Go Wes Go!!!!! |
|
| Author: | Reed [ Thu Mar 13, 2025 3:53 pm ] |
| Post subject: | Re: Volare project |
Baby steps and diligence will get you there. Keep at it! |
|
| Author: | Wesola78 [ Sun Mar 16, 2025 10:59 am ] |
| Post subject: | Re: Volare project |
Dennis and Reed, thanks for the encouragement. I now have the replacement slant six on the engine stand, almost in the upright position. Question: Right now the replacement slant doesn't have the intake and exhaust manifolds on it. Can I install them now, before the engine is swapped in? Is this a good idea? It seems like it would be easier from a labor standpoint. Let me know, thanks! |
|
| Author: | slantzilla [ Sun Mar 16, 2025 11:30 am ] |
| Post subject: | Re: Volare project |
I rarely use an exhaust manifold, but if you put the motor in with them on, it might make a couple bellhousing bolts a little tougher to get in, but nothing too serious. |
|
| Author: | Wesola78 [ Sun Mar 16, 2025 11:35 am ] |
| Post subject: | Re: Volare project |
Ok, so its a trade off. ThanKs for the reply. |
|
| Author: | volaredon [ Mon Mar 17, 2025 10:48 am ] |
| Post subject: | Re: Volare project |
I've put them in with and I've put them in without, not a lot of difference, except for it might be easier to get at the bottom center intake bolts while on a stand.. the last couple of manifolds I pulled were on a volare (not mine) in a junkyard Hey Wes a question Would you have any "doubles" / extras for AC brackets? Once you're in and running let me know if you do. But don't get rid of them til you have the replacement in place, make sure they're gonna be "extras" first. What's with the replacement engine? Freshly overhauled? Hopped up? Low mile takeout? None of those? Now you gonna rebuild the original and hop that one up to go back in at some point? Plenty of builds and people who have been there to guide you right here if you do .. |
|
| Author: | Wesola78 [ Tue Mar 18, 2025 6:50 am ] |
| Post subject: | Re: Volare project |
Hey Don, I was thinking it would be easier to get at some of those manifold bolts while its on an engine stand. The replacement slant six is a low mileage engine. I just want to get the Volare back on the road for now. I’m pretty sure I don’t have any AC brackets, but I’ll keep a lookout as I go through my parts. Thanks for your response! |
|
| Author: | Wesola78 [ Tue Mar 18, 2025 6:54 am ] |
| Post subject: | Re: Volare project |
I’ll keep the original slant, its got a lot of miles on it, and it was smoking the last time it ran. So I guess it would need to be bored and honed at a machine shop. But thats for the future. |
|
| Page 2 of 2 | All times are UTC-07:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|