Slant Six Forum https://slantsix.org/forum/ |
|
Covalt - "Project 65 Valiant" https://slantsix.org/forum/viewtopic.php?t=35632 |
Page 118 of 124 |
Author: | hyper_pak [ Sat Dec 02, 2023 4:51 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Pretty cool linkage Rick! |
Author: | Rick Covalt [ Sat Dec 02, 2023 5:21 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
I been banging gears all day up in the garage! If feels really good! I sure like a 4 speed! ![]() ![]() |
Author: | slantzilla [ Sat Dec 02, 2023 7:11 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Project creep. ![]() |
Author: | Dart270 [ Sun Dec 03, 2023 1:11 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Very cool, Rick. Glad you are pursuing your dreams and making them happen, one shift linkage at a time. I want a ride in that car!! Lou |
Author: | Andrew Shank [ Mon Dec 04, 2023 9:20 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
You should Lou, its quite fun! Can't wait till the 4 speed is in and he's doing wheel stands! ![]() |
Author: | Rick Covalt [ Mon Dec 04, 2023 5:33 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Quote: he's doing wheel stands!
When/if the wheels leave the ground I will need to have on my depends! ![]() ![]() I don't think I need to worry about that just yet! |
Author: | Greg Ondayko [ Mon Dec 04, 2023 6:55 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Looking good. You may want to order those loose parts for the 833 from brewer's instead of passion in the future. Get that 4-speed od in there and prepare to go slooow. But hey you can run on I70 / 81 for more than 1 minute and keep up with traffic in the OD gear! |
Author: | Rick Covalt [ Tue Dec 05, 2023 3:09 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
I tried Brewers and they do no have the 1/2 shift fork in stock. And they had no used stock. It will be interesting to see just how much slower it is. In a really light car with 275 ish HP, I don't think it will be nearly as bad as it would be in a 3500 truck with 100 hp. Maybe some day I will run into a Tremec TKO or something for cheap. Then I will have to cut up the cross member.......etc. More project creep. ![]() ![]() Quote: But hey you can run on I70 / 81 for more than 1 minute and keep up with traffic in the OD gear!
My only debate is with how low of a gear to run. It will be at least 4.10, but 4.30 and 4.56 are a possibility.
|
Author: | Greg Ondayko [ Tue Dec 05, 2023 5:58 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
that's an easy swap if you have 3 little piggies built. |
Author: | Dart270 [ Tue Dec 05, 2023 6:03 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
3.73s are good to cruise to Sebring, FL or Woodburn, OR and back at 75+ MPH. I'd start with 4.10s and see how they fly, if in stock already, or just stick with your 4.30s. Lou |
Author: | Rick Covalt [ Tue Dec 05, 2023 6:36 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
I was leaning towards the 4.10 also. I can test the 4.30s but they are on a spool. I also have 4.56s but they sing a bit too much for a a long term solution. |
Author: | slantzilla [ Tue Dec 05, 2023 7:13 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Doesn't the OD trans have a 3.09 1st gear? With a 4.56 you should drag the back bumper. |
Author: | Rick Covalt [ Tue Dec 05, 2023 9:06 am ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Yes it does, And so does the non OD 833 that I have out of the early 6 cylinder cars. |
Author: | Rick Covalt [ Wed Jan 24, 2024 5:57 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Tore apart, cleaned, lubricated two 4 speed Hurst shifters. Also welded on half nuts and tapped the main body for stops. These old Competition plus shifters didn't have them. They do now! ![]() Where is that old shirt I had? "Shift as hard as you like, but don't break your wrist!" ![]() |
Author: | slantzilla [ Wed Jan 24, 2024 6:01 pm ] |
Post subject: | Re: Covalt - "Project 65 Valiant" |
Watch video of Ronnie Sox or Herb McCandless and shift accordingly. ![]() |
Page 118 of 124 | All times are UTC-07:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |