WOW 5 pages of antagonizing and advertising in a Q&A forum.
I am not impressed.
| Slant Six Forum https://slantsix.org/forum/ |
|
| Slant 6 Superchargers https://slantsix.org/forum/viewtopic.php?t=15724 |
Page 5 of 5 |
| Author: | Rug_Trucker [ Sun Feb 28, 2010 6:01 am ] |
| Post subject: | |
Quote: Where's that pic from? Looks pretty good....
That is probably from the super charger store they sell the kit |
|
| Author: | Tim Keith [ Sun Feb 28, 2010 8:22 am ] |
| Post subject: | |
There are links for two slant six cars in the store's site. |
|
| Author: | Chuck [ Sun Feb 28, 2010 9:25 am ] |
| Post subject: | |
Very nice pic! |
|
| Author: | nwstal [ Sun Feb 28, 2010 2:25 pm ] |
| Post subject: | |
That setup looks sweet clean and professional install. What about the power level though? That's a centrifugal though no low end boost but still looks mean and clean. On a side note, I'm working on boost:pulley ratios for the M90 on the SL6 and If anyone wants me to post them here just let me know. It's quite a bit of calculations involved. Will be working on Turbo Sizing and other research data. I would suppose that this would merit a new thread but I don't want to clog the board, so a moderator could let me know here what if any info they want posted here. |
|
| Author: | Tim Keith [ Sun Feb 28, 2010 8:49 pm ] |
| Post subject: | |
One of the slant sixes was built mostly for show for a '64 Valiant. I think it made about 230 HP. The other had more boost. The store site has a good writeup on the 2 cars, as well as several V8s. http://thesuperchargerstore.com/ |
|
| Author: | Wesd100 [ Tue Apr 03, 2018 4:08 pm ] |
| Post subject: | Re: Slant 6 Superchargers |
Looked at the website, and can't find the supercharger kit got /6. Anyone know if they still make these? |
|
| Author: | bboogieart [ Sun Apr 08, 2018 10:16 am ] |
| Post subject: | Re: Slant 6 Superchargers |
WOW 5 pages of antagonizing and advertising in a Q&A forum. I am not impressed.
|
|
| Author: | GTS225 [ Sun Apr 08, 2018 10:27 am ] |
| Post subject: | Re: Slant 6 Superchargers |
Quote: WOW 5 pages of antagonizing and advertising in a Q&A forum.
**************************************************************I am not impressed. That's five pages of antagonizing and advertising, spread out over 12 years, in a Q&A forum. And we don't discuss these things to impress you, we discuss these things to decide if there's any merit in pursuing them. Roger |
|
| Author: | Vettefab [ Thu Apr 12, 2018 5:23 am ] |
| Post subject: | Re: Slant 6 Superchargers |
Just saw that yesterday :   I'm scared about the angle between the crankshaft-to-blower belt and the blower drive shaft to head distance... Won't this setup pop out some manifold-head studs or tear the manifold to head flange !? |
|
| Author: | DadTruck [ Thu Apr 12, 2018 6:55 am ] |
| Post subject: | Re: Slant 6 Superchargers |
I am thinking there is an additional bracket under the intake that attaches to the block/motor mount. |
|
| Author: | Dart270 [ Thu Apr 12, 2018 8:22 am ] |
| Post subject: | Re: Slant 6 Superchargers |
Note that you can pull an engine using the intake. There are a lot of 5/16" studs/nuts there. Yes, you could also make an additional support. Lou |
|
| Page 5 of 5 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|