Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 12:22 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Sat Nov 05, 2005 5:12 pm 
Offline
TBI Slant 6
User avatar

Joined: Wed Jun 29, 2005 7:34 am
Posts: 222
Location: Boulder Colorado
Car Model:
So last night I printed out SS Dan's instructions for valve lash and today I took on the task. A bit nerve racking with your hand moving up and down as you make adjustments, but the most beautiful thing happened:

I did all the exhaust valves first, then started on the intake valves. All valves were loose. I got to the last 2 valves, gave them both a twist to tighten and all of a sudden there was this silence. No more clatter of rockers on valves. I could hardly believe it. I had been so used to that soft clacking I didn't know it wasn't supposed to be there.

However, I do have a problem. After I finished my valve lash I shut off the car, hooked up a timing light with the valve cover still off. Turned her right back on, still warm and adjusted idle speed back to 800 and timing to TDC with the hose to the dist. plugged and the car in park. Her idle was still rough in park. But when I put her in gear the idle was terrible.

I checked the no 1 plug with the timing light to see if it was firing regularly. It fired great in park and great in gear. I then checked the no 6 plug. It fired great in park BUT it missed frequently in gear.

What would cause the no 6 plug to fire well in park but poorly in reverse?

I pulled the no 6 plug and it was black with carbon but showed no signs of wetness or physical damage.

Will the car run poorly in gear until I put the valve cover back on?

I plugged the holes that go to the PCV, oil breather and dist advance on the carb. but the air cleaner was off. Do I need the air cleaner on?

Are you supposed to have the air cleaner on when you adjust idle speed and timing?

I also tried advancing the spark (turning dist. counter clockwise) but that did not help.

Car ran a little rough before the adjustment but nothing like this. And the valves sound much smoother than they used to.

Any help/input is GREATLY appreciated.

_________________
God took you away, then brought you back to me.
Image


Top
   
 Post subject:
PostPosted: Sat Nov 05, 2005 5:28 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
The air cleaner doesn't matter, but the PCV valve does.

The carb is calibrated for the PCV air 'leak'. With it plugged up you're not getting as much air as is expected and are going to be rich.........

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Sat Nov 05, 2005 5:34 pm 
Offline
TBI Slant 6
User avatar

Joined: Wed Jun 29, 2005 7:34 am
Posts: 222
Location: Boulder Colorado
Car Model:
Does that mean I need to put the valve cover back on and hook up the pcv before I tune (and freak out.) ?

Would running rich really make that no 6 plug fire so terribly when in gear?

_________________
God took you away, then brought you back to me.
Image


Top
   
 Post subject:
PostPosted: Sat Nov 05, 2005 5:44 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
hook up the pcv valve and hose to the carb.

The pcv valve doesn't need to be in the valve cover and the valve cover doesn't need to be on the engine.................

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Sat Nov 05, 2005 5:45 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
With a bad mixture, anything can happen...........


I'd also check the resistance of the plug wires to see if there's a bad wire.............

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Sat Nov 05, 2005 6:04 pm 
Offline
TBI Slant 6
User avatar

Joined: Wed Jun 29, 2005 7:34 am
Posts: 222
Location: Boulder Colorado
Car Model:
how do i check the resistance in the plug wires?
plugs are brand new, 50 miles.
plug wires are 3 months old but i have had them fail straight out of the box before.
still, one would assume they would fail equally in park and reverse...

_________________
God took you away, then brought you back to me.
Image


Top
   
 Post subject:
PostPosted: Sun Nov 06, 2005 3:52 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
Even if the plugs are new, if they are black with soot/carbon, the spark can short to ground, instead of jumping the gap. When the car is put in gear, the load on the plug increases. When this happens the spark will travel down the carbon path of the plug, and will not create a large enough magnetic field in the wire to trigger the timing light. Clean the plugs, or install another set of new ones. Make sure the carb in not too rich, or you will foul the new plugs, also. Check the float and choke.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Sun Nov 06, 2005 8:31 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Quote:
how do i check the resistance in the plug wires?
plugs are brand new, 50 miles.
plug wires are 3 months old but i have had them fail straight out of the box before.
still, one would assume they would fail equally in park and reverse...

You need an ohmmeter (usually it's part of a voltmeter). All the wire should be about the same resistance. Although at 3 months they should be good.

I've had them fail out of the box too. Went back to the auto parts store with the ohmmeter to check the replacement set before I took it home.

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Sun Nov 06, 2005 9:41 pm 
Offline
TBI Slant 6
User avatar

Joined: Wed Jun 29, 2005 7:34 am
Posts: 222
Location: Boulder Colorado
Car Model:
so after reading your posts it seemed obvious that the fuel fouling was the source of my rough idle. i removed and cleaned the plugs, replaced the valve cover and hooked the pcv valve back up and then dialed the fuel/air mix back 1/4 turn. i started the car with baited breath and vrooom. the smoothest idle my dart has ever had. it was beautiful. thank you all. so many people have talked smack about this car. but the only thing wrong with it is my lack of experience as a mechanic. with your help, she is realizing her full potential and i am showing the rest of the world how beautiful a 75 can be.

_________________
God took you away, then brought you back to me.
Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 9 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 9 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited