Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 6:26 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Erson cam?
PostPosted: Wed Nov 09, 2005 6:51 am 
Offline
3 Deuce Weber
User avatar

Joined: Thu Dec 04, 2003 12:47 pm
Posts: 80
Car Model:
Has anyone used one of these cams from Summit Racing?
I am in the process of building a dedicated drag motor and found that they offer this cam with a .510 lift.
Next question would be if I could use it with .090 off of the head without piston clearance problems?


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 7:06 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 17687
Location: Blacksburg, VA
Car Model:
I haven't used that, but looks like nice specs. You should use 9.5:1 comp minimum. 0.090" (or even 0.140") off the head will give no clearance problems with that cam in a 225.

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 8:14 am 
Offline
3 Deuce Weber
User avatar

Joined: Thu Dec 04, 2003 12:47 pm
Posts: 80
Car Model:
Thanks, Lou. I had thought about taking .100 off the head, but was going to be safe with .090.


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 8:28 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
Hey, Robert. Good to see you back. Is that for the 66 Valiant? How is the car coming? I was going to give you a holler, but misplaced your e-mail address.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 8:53 am 
Offline
3 Deuce Weber
User avatar

Joined: Thu Dec 04, 2003 12:47 pm
Posts: 80
Car Model:
No Charlie, the 66 found a new home in Jacksonville.
This is for a rail that I am building for a new type of class racing an internet group has started.
It has to be pre 62 vintage type. Motors, carbs, ignition has to be from that era.
One of the cars that is racing this class is a 261 GMC, running twin carbs with a glide tranny behind it and he is turning low 13's at this time. He has run a 12.99 with it. The motor is basically stock and the cars are weighing in around 1300 pounds.
Hopefully I can get the 225 to turn some of these low times. There are a couple of flatheads running, but they are in the 13's.
This is a heads up class, so the first one there is the winner.
I will try and email you later on this month and you can get my address again.


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 10:01 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 17687
Location: Blacksburg, VA
Car Model:
Robert,

If you are really going to race, I'd do a combo - 0.100 off the block deck and 0.080" off the head. Or, 0.120" off the head or block would work safely. You'll be around 10.2-11:1 and I bet valve/piston will still be fine with that cam.

Keep us posted...

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 10:09 am 
Offline
3 Deuce Weber
User avatar

Joined: Thu Dec 04, 2003 12:47 pm
Posts: 80
Car Model:
Lou, I will definitely be doing this. I'll probably only take .100 off of the head as the block is already built except for the cam and timing gears.
One other limiting factor I forgot to mention, I can only run 6" bias ply tires in this class. I can't get so much hp that I spin the tires off the line.
I will be running a standard transmission and that is going to hurt a little bit.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 7 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Bing [Bot] and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited