The trans ID is stamped on the driver's side of the pan rail. Clean all the grease and gunk off the side of the rail, indicated by the green arrows in the photo below, and report what you find:
| Slant Six Forum https://slantsix.org/forum/ |
|
| Idenification time again (Picture) https://slantsix.org/forum/viewtopic.php?t=18904 |
Page 1 of 1 |
| Author: | Bren67Cuda904 [ Sat Jul 29, 2006 5:54 pm ] |
| Post subject: | Idenification time again (Picture) |
This trans was pulled from a 68 dart that didn't have the orignal slant. Can we tell what year this trans is? Numbers on bellhousing read- 871-2 both sides http://www.renaissanceracing.com/images/Trans904.JPG http://www.renaissanceracing.com/images ... erSide.JPG |
|
| Author: | SlantSixDan [ Sat Jul 29, 2006 6:08 pm ] |
| Post subject: | |
The trans ID is stamped on the driver's side of the pan rail. Clean all the grease and gunk off the side of the rail, indicated by the green arrows in the photo below, and report what you find:
|
|
| Author: | Bren67Cuda904 [ Sat Jul 29, 2006 8:21 pm ] |
| Post subject: | |
findings- 2538337Y 2017190 |
|
| Author: | SlantSixDan [ Sat Jul 29, 2006 8:55 pm ] |
| Post subject: | |
That there is an early-production 1966-model A904G originally used behind a 225 engine. |
|
| Author: | Bren67Cuda904 [ Sun Jul 30, 2006 4:41 am ] |
| Post subject: | |
The big red X on the bellhousing- whats that all about? Not orignal? |
|
| Author: | Reed [ Sun Jul 30, 2006 8:57 am ] |
| Post subject: | |
"X" marks the spot! It means you found the treasure! Seriously though, who knows? Most factory markings I have seen were made with grease pencil, not spray paint. That tranny has been floating around for 40 years. Who knows where that X came from or what it means. |
|
| Author: | Bren67Cuda904 [ Sun Jul 30, 2006 1:05 pm ] |
| Post subject: | |
This is the trans is the Barracuda. Its is thought to be orignal. 2801533Y 2539494 |
|
| Author: | SlantSixDan [ Sun Jul 30, 2006 1:22 pm ] |
| Post subject: | |
Yep, that is an ID number for a 1967 A904G used behind a 225 engine. |
|
| Author: | Bren67Cuda904 [ Mon Oct 09, 2006 1:37 pm ] |
| Post subject: | |
I think I found a large input shaft A904 that will work in my 67 Barracuda with large crank flange. PK4028405 57028220 What do you think? Can I use the input shaft in my 67 A904? |
|
| Author: | Bren67Cuda904 [ Tue Oct 10, 2006 6:42 am ] |
| Post subject: | |
Is the input shaft in this transmission (PK4028405 57028220) A large input shaft type? It is bolted to a 1972 225, which makes me beleive there is a very good possability that it is. If so will it swap in to this small input shaft transmission (2538337Y 2017190)? Which is an early-production 1966-model A904G. |
|
| Author: | Bren67Cuda904 [ Tue Oct 10, 2006 7:35 pm ] |
| Post subject: | |
Is this trans number to distorted to decode? PK4028405 57028220 |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|