You could relocate them to the trunk next to your battery.
| Slant Six Forum https://slantsix.org/forum/ |
|
| Rerouting question https://slantsix.org/forum/viewtopic.php?t=22777 |
Page 1 of 1 |
| Author: | skraecken [ Wed Apr 18, 2007 12:15 pm ] |
| Post subject: | Rerouting question |
Dan had a good idea about rerouting the fuel line. But. Is there some rerouting thats possible with the heater hoses? (Valiant -66) |
|
| Author: | SlantSixDan [ Wed Apr 18, 2007 12:52 pm ] |
| Post subject: | |
What do you wish to achieve? |
|
| Author: | emsvitil [ Wed Apr 18, 2007 1:36 pm ] |
| Post subject: | |
What could you do with the heater hoses that wouldn't make it more complicated? Mine are the simplest layout I've ever seen on a car....... |
|
| Author: | Bren67Cuda904 [ Wed Apr 18, 2007 3:21 pm ] |
| Post subject: | |
You could relocate them to the trunk next to your battery.
|
|
| Author: | skraecken [ Sun Apr 22, 2007 11:32 am ] |
| Post subject: | |
Quote: What do you wish to achieve?
It would be easier to remove the valvecover.
|
|
| Author: | 61 V200 [ Sun Apr 22, 2007 11:51 am ] |
| Post subject: | |
Get longer hoses and route them along the inside of the right fender |
|
| Author: | 61 V200 [ Sun Apr 22, 2007 11:57 am ] |
| Post subject: | |
|
|
| Author: | skraecken [ Sun Apr 22, 2007 11:58 am ] |
| Post subject: | |
It is the "bend" at the firewall that I not like, its hard to get the hoses direct 90 degr. |
|
| Author: | Rust collector [ Sun Apr 22, 2007 12:59 pm ] |
| Post subject: | |
Get 2 90 degree pipe bends, and some longer hoses... Put the bends just off the firewall, and route the hoses over the inner fender |
|
| Author: | Aggressive Ted [ Sun Apr 22, 2007 2:12 pm ] |
| Post subject: | |
I can send you some pictures if you send me your email. I routed mine over the top of the engine to help keep them warm. Everything is nice and neat and get plenty of air. My SL6 runs so cold it isn't funny, everything is new including radiator and heater core, 195 stat and she runs 130 to 145 degrees. A little over 10,000 miles on the rebuild. Can't seem to add any pictures to my signature block like most folks do or to the post for that matter. |
|
| Author: | emsvitil [ Sun Apr 22, 2007 2:37 pm ] |
| Post subject: | |
Quote: Get 2 90 degree pipe bends, and some longer hoses...
Put the bends just off the firewall, and route the hoses over the inner fender Copper plumbing elbows work great for tight bends................ |
|
| Author: | Charrlie_S [ Sun Apr 22, 2007 3:45 pm ] |
| Post subject: | |
Most part stores have a "cut to length" long hose, with a 90 degree bend on one end. |
|
| Author: | Aggressive Ted [ Mon Apr 23, 2007 8:34 am ] |
| Post subject: | Reouting hoses |
Send me your email and I will send you some pictures. |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|