| Slant Six Forum https://slantsix.org/forum/ |
|
| Harmonic Balancers https://slantsix.org/forum/viewtopic.php?t=2403 |
Page 1 of 1 |
| Author: | Andyman225 [ Sun Jul 15, 2001 3:17 am ] |
| Post subject: | Harmonic Balancers |
Hey guy's I just tore down my 64 to put a new cam in it(clifford 260)and found alot more than I bargianed for. To make a long story short I'm about to have the long block rebuilt(1.78" In 1.4" Exh ported and bench flowed head, rotating assemebly balanced, and stock compression for turbo I'm putting together)and I need a new harmonic balancer. My old one broke when I pulled it off(casting split) and all the places I've gone say that they don't exist new , or rebuilt any more. I think they are full of s**t, but haven't yet forund a supplier for a stock or rebuilt one. Can you point me in the right direction? andyman225_99@yahoo.com |
|
| Author: | MrMopar [ Sun Jul 15, 2001 7:53 am ] |
| Post subject: | Re: Harmonic Balancers |
Quote:
: Hey guy's I just tore down my 64 to put a new : cam in it(clifford 260)and found alot more : than I bargianed for. To make a long story : short I'm about to have the long block : rebuilt(1.78" In 1.4" Exh ported : and bench flowed head, rotating assemebly : balanced, and stock compression for turbo : I'm putting together)and I need a new : harmonic balancer. My old one broke when I : pulled it off(casting split) and all the : places I've gone say that they don't exist : new , or rebuilt any more. I think they are : full of s**t, but haven't yet forund a : supplier for a stock or rebuilt one. Can you : point me in the right direction? Clifford has a raceing one but it's over $300 bucks............ I ran across a rebilder when I was looking for pulleys I'll see if I can find it again and post it |
|
| Author: | Will [ Sun Jul 15, 2001 8:07 am ] |
| Post subject: | Re: Harmonic Balancers |
You can get a Fisher from clifford or use a big block one from summit, such as a fluiddamper. All you have to do is change to a differnt seal. A big block one may work I dont know about the outside dia. off hand. Will Quote:
: Hey guy's I just tore down my 64 to put a new : cam in it(clifford 260)and found alot more : than I bargianed for. To make a long story : short I'm about to have the long block : rebuilt(1.78" In 1.4" Exh ported : and bench flowed head, rotating assemebly : balanced, and stock compression for turbo : I'm putting together)and I need a new : harmonic balancer. My old one broke when I : pulled it off(casting split) and all the : places I've gone say that they don't exist : new , or rebuilt any more. I think they are : full of s**t, but haven't yet forund a : supplier for a stock or rebuilt one. Can you : point me in the right direction? slantsix@netzero.net |
|
| Author: | MrMopar [ Sun Jul 15, 2001 8:14 am ] |
| Post subject: | Re: Harmonic Balancers |
Here's some rebuilders some do have stock on hand Winslow Mfg; 5700 Dean Ave; Raleigh NC 27604; 919-790-9713 Damper Dudes; 5509 Cedars Rd #2; Redding CA 96001; 800-413-2673 (orders) or 916-244-7225 (info) Damper Doctor; 1055 Parkview Ave; Redding CA 96001; 916-246-2984 Hope this helps Quote:
:
: Hey guy's I just tore down my 64 to put a new : cam in it(clifford 260)and found alot more : than I bargianed for. To make a long story : short I'm about to have the long block : rebuilt(1.78" In 1.4" Exh ported : and bench flowed head, rotating assemebly : balanced, and stock compression for turbo : I'm putting together)and I need a new : harmonic balancer. My old one broke when I : pulled it off(casting split) and all the : places I've gone say that they don't exist : new , or rebuilt any more. I think they are : full of s**t, but haven't yet forund a : supplier for a stock or rebuilt one. Can you : point me in the right direction? |
|
| Author: | dschumers [ Sun Jul 15, 2001 8:41 am ] |
| Post subject: | Damper Doctors |
Quote:
: Hey guy's I just tore down my 64 to put a new : cam in it(clifford 260)and found alot more : than I bargianed for. To make a long story : short I'm about to have the long block : rebuilt(1.78" In 1.4" Exh ported : and bench flowed head, rotating assemebly : balanced, and stock compression for turbo : I'm putting together)and I need a new : harmonic balancer. My old one broke when I : pulled it off(casting split) and all the : places I've gone say that they don't exist : new , or rebuilt any more. I think they are : full of s**t, but haven't yet forund a : supplier for a stock or rebuilt one. Can you : point me in the right direction? Damper Doctors 1055 Parkview Avenue Redding, CA 96001 They are a damper rebuilder. Dennis aschumers@aol.com |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|