Slant Six Forum :: supersixcarb

: Does anyone know where I actually find a carter
: super six carb - I see them mentioned
: everywhere and that I should check boneyards
: - but ya know - I have and they aint
: around!!
:
: Thanks! Even new would be great!

:
: Chuck, I think you are more than correct!
: I can't find a 2 barrel anywhere here in
: northern CA. Only one I have been able to
: get ahold of is a Rochester that is loaded
: with connections and holes that I can only
: guess as to what connects to them! I did
: find a number on it and it's listed in my
: Chiltons but no diagrams as to what connects
: where. Since I am running a '69 vehicle I
: only need to connect the fuel and a line for
: the vacuum advance on the distributor and a
: line to the PCV and that leaves about 3 more
: holes in the damn thing than I need!
:
: Oh well, guess I will just keep looking and
: hoping to find a good 2 barrel or just go
: looking for a 390 to put on it.
:
: Later,
: Dan
:
: "I may be slow, but at least I'm not very
: fast!"

: OK, who wants my super six carb? Manifold? I am
: in norther ca. It's a naked 49 stater from
: texas. I was thinking $40/best offer for the
: carb and same for the manifold. Make an offer, I might not refuse it.

Author:	boomerswagon [ Wed Jan 09, 2002 9:51 pm ]
Post subject:	supersixcarb
Does anyone know where I actually find a carter super six carb - I see them mentioned everywhere and that I should check boneyards - but ya know - I have and they aint around!! Thanks! Even new would be great! highwater@juno.com

Author:	Kevin Barnwell [ Thu Jan 10, 2002 5:17 am ]
Post subject:	Re: supersixcarb
Quote: : Does anyone know where I actually find a carter : super six carb - I see them mentioned : everywhere and that I should check boneyards : - but ya know - I have and they aint : around!! : : Thanks! Even new would be great! When I did my conversion on my 73 Duster, I just got a Carter 2bbl from a 73 318. That way it would have the same vacuum ports, etc. ktbarnwell1@juno.com

Author:	Johnny Z [ Thu Jan 10, 2002 9:20 pm ]
Post subject:	Re: supersixcarb
Kragen Auto,Carter bbd off of a early(no smog)318 mopar.Get the one rebuilt by Holley,cost me $120.00.Good Luck!! johnfzirbel@mindspring.com

Author:	Chuck Rivers [ Sat Jan 12, 2002 5:06 pm ]
Post subject:	Re: supersixcarb
Quote: : Does anyone know where I actually find a carter : super six carb - I see them mentioned : everywhere and that I should check boneyards : - but ya know - I have and they aint : around!! : : Thanks! Even new would be great! I found a bunch in a yard in Florida, bought two that still had the tag on them and had one of thew rebuild. I believe they are more readily available on the east coast. Donors are Aspens and Volares. Chuck webmaster@omnipages.com

Author:	ron parker [ Sat Jan 12, 2002 5:33 pm ]
Post subject:	Re: supersixcarb
boomerwagon i have a holley supersix carb and manifold that i ran on my car 3 years ago. the carb will probbaly have to be rebuilt but it ran good while on the car. the car picked up about .2 in the 1/8. you can have the carb if you can pay for shiping or see me at one of the /6 races thanks ron parker rpracing@catt.com

Slant Six Forum https://slantsix.org/forum/

supersixcarb https://slantsix.org/forum/viewtopic.php?t=3090	Page 1 of 1

Author:	WhaleMstr [ Sun Jan 13, 2002 9:58 am ]
Post subject:	Re: supersixcarb
Chuck, I think you are more than correct! I can't find a 2 barrel anywhere here in northern CA. Only one I have been able to get ahold of is a Rochester that is loaded with connections and holes that I can only guess as to what connects to them! I did find a number on it and it's listed in my Chiltons but no diagrams as to what connects where. Since I am running a '69 vehicle I only need to connect the fuel and a line for the vacuum advance on the distributor and a line to the PCV and that leaves about 3 more holes in the damn thing than I need! Oh well, guess I will just keep looking and hoping to find a good 2 barrel or just go looking for a 390 to put on it. Later, Dan "I may be slow, but at least I'm not very fast!"

Author:	Richard [ Sun Jan 13, 2002 4:25 pm ]
Post subject:	Re: supersixcarb
OK, who wants my super six carb? Manifold? I am in norther ca. It's a naked 49 stater from texas. I was thinking $40/best offer for the carb and same for the manifold. Would recomend a dual stage webber instead, or the 390 (yeah, I like the 390!!!!!!!!!!) Quote: : : Chuck, I think you are more than correct! : I can't find a 2 barrel anywhere here in : northern CA. Only one I have been able to : get ahold of is a Rochester that is loaded : with connections and holes that I can only : guess as to what connects to them! I did : find a number on it and it's listed in my : Chiltons but no diagrams as to what connects : where. Since I am running a '69 vehicle I : only need to connect the fuel and a line for : the vacuum advance on the distributor and a : line to the PCV and that leaves about 3 more : holes in the damn thing than I need! : : Oh well, guess I will just keep looking and : hoping to find a good 2 barrel or just go : looking for a 390 to put on it. : : Later, : Dan : : "I may be slow, but at least I'm not very : fast!" Richard-c@e-d-a.com

Author:	Richard [ Sun Jan 13, 2002 4:29 pm ]
Post subject:	Re: supersixcarb
Quote: : OK, who wants my super six carb? Manifold? I am : in norther ca. It's a naked 49 stater from : texas. I was thinking $40/best offer for the : carb and same for the manifold. Make an offer, I might not refuse it. Would : recomend a dual stage webber instead, or the : 390 (yeah, I like the 390!!!!!!!!!!) OOPS <A HREF="mailto:Richard-c@e-d-a.com">Richard-c@e-d-a.com</A> Richard-c@e-d-a.com

Page 1 of 1	All times are UTC-08:00
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/