| Slant Six Forum https://slantsix.org/forum/ |
|
| head gasket sealer question https://slantsix.org/forum/viewtopic.php?t=33262 |
Page 1 of 1 |
| Author: | kenicb [ Sat Jan 10, 2009 2:25 pm ] |
| Post subject: | head gasket sealer question |
Dodge manual 9-9 cylindar head installation step 3) "coat new gasket lightly with chrysler sealer part number 1057794 or equivalent. Install gasket and cylinder head." what is the equivalent? neither me nor the parts store was sure if hi temp silicone is an equivalent. I am using a standard felpro gasket thanks so much. Keni |
|
| Author: | SlantSixDan [ Sat Jan 10, 2009 2:29 pm ] |
| Post subject: | |
That instruction was for the OE-type shim steel gasket. Strictly speaking you don't need sealant with the composition type head gasket, though it is good insurance to coat both sides with something good like copper gasket spray ("Copper Cote", "Copper Spray-A-Gasket", etc.) |
|
| Author: | kenicb [ Sat Jan 10, 2009 8:20 pm ] |
| Post subject: | |
Thanks Dan da Man. I will look for the spray type sealent and save the hi-temp silicone for the manifold gasket. I will have the engine back together this month and will post pics and a step by step recount of how to change your piston rings with the engine still in the car. Ilearned a lot and appreciate your help throughout the process. Stay warm Keni |
|
| Author: | Rug_Trucker [ Thu Jan 15, 2009 8:17 am ] |
| Post subject: | |
I magine that, a Nashvillian on this board that plays guitar! Just stopped by to say "howdy!" Nice Website. |
|
| Author: | kenicb [ Thu Jan 15, 2009 10:54 am ] |
| Post subject: | nashville |
Howdy back. Love it here. Love what I do. When I'm off the road and home working the cars are a good source of quiet therapy. Quiet. Ahhhhh And thanks for visiting the web site. Hope to run into out there at a show soon. Until then, stay strong. God bless Keni |
|
| Author: | SlantSixDan [ Thu Jan 15, 2009 10:56 am ] |
| Post subject: | |
Quote: Thanks Dan da Man. I will look for the spray type sealent and save the hi-temp silicone for the manifold gasket.
Mmm...glad to help, but don't goop the manifold gasket with sillycone. It is very much worth your while to get the good gaskets for the manifolds-to-head and intake-to-exhaust junctions.
|
|
| Author: | 6shotvanner [ Thu Jan 15, 2009 2:37 pm ] |
| Post subject: | |
Keni,I am somewhat slow on the uptake,finally tried the little red klicky for your web site.OMG you're that Keni!! Been listening to you're tunes/lyrics for awhile,my 18yr old granddaughter is a fan(me to).You get quiet therapy with slant6 tinkering,I get to slant6 tinker and crank up "Gunslinger"  God Bless young man and thanks 
|
|
| Author: | Rug_Trucker [ Thu Jan 15, 2009 3:55 pm ] |
| Post subject: | |
Keni ever have time for a good 'ol Nashville "guitar pull" Mopar/music BBQ! Got some wompin musicians around here. Show you some slant experimints etc. 
|
|
| Author: | SlantSixDan [ Thu Jan 15, 2009 9:22 pm ] |
| Post subject: | |
Quote: I magine that, a Nashvillian on this board that plays guitar!
Well, after all, there's thirteen hundred and fifty two guitar pickers in Nashville…
|
|
| Author: | Charrlie_S [ Fri Jan 16, 2009 5:13 am ] |
| Post subject: | |
Quote: Quote: I magine that, a Nashvillian on this board that plays guitar!
Well, after all, there's thirteen hundred and fifty two guitar pickers in Nashville… 
|
|
| Author: | Rug_Trucker [ Fri Jan 16, 2009 2:58 pm ] |
| Post subject: | |
Quote: Quote: I magine that, a Nashvillian on this board that plays guitar!
Well, after all, there's 22 thousandand fifty two guitar pickers in Nashville… |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|