| Slant Six Forum https://slantsix.org/forum/ |
|
| Arp group buy? https://slantsix.org/forum/viewtopic.php?t=37222 |
Page 1 of 5 |
| Author: | wvenable [ Thu Sep 24, 2009 11:13 am ] |
| Post subject: | Arp group buy? |
Anyone in need of ARP products? I am thinking of buying some things and would be willing to do some legwork to see if this is feasable. Any suggestions would be welcome. Thanks, Wayne. |
|
| Author: | 66aCUDA [ Thu Sep 24, 2009 4:33 pm ] |
| Post subject: | |
I would be interested in 2 complete engine sets and an extra rod set. Frank |
|
| Author: | ceej [ Thu Sep 24, 2009 4:49 pm ] |
| Post subject: | |
I'm interested. Let me know what you come up with! CJ |
|
| Author: | Greg Ondayko [ Thu Sep 24, 2009 6:22 pm ] |
| Post subject: | |
I''m in the market for Head bolts, Rod Bolts and Main Cap Bolts - and one of the Nice ford Cam bolts for the Slant Cam buttom. Greg |
|
| Author: | HyperValiant [ Thu Sep 24, 2009 7:58 pm ] |
| Post subject: | |
Im interested in head ,rod,and main bolts. |
|
| Author: | DadTruck [ Thu Sep 24, 2009 9:23 pm ] |
| Post subject: | Arp |
let me know pricing that you can get on main and head bolts, already have the rod bolts |
|
| Author: | lowbudget [ Fri Sep 25, 2009 12:42 am ] |
| Post subject: | |
I'd be interested in a set. You can't go wrong with ARP products. I figure if I build something I might as well build it as stout as possible. |
|
| Author: | wvenable [ Fri Sep 25, 2009 4:52 am ] |
| Post subject: | |
Lowbudget, that is my thinking as well. I have located a truck crank, two BH blocks to choose from, and will be going the k1/Wiseco route. Ordering the ARP goodies may be overkill but I would much rather over-engineer this than go conservative. Guys thank you for the interest. Maybe more will join in today. Next week I was thinking about contacting ARP directly and see if they could recommend one of their jobbers/venders that might like to work with us. Thanks again, Wayne. |
|
| Author: | Charrlie_S [ Fri Sep 25, 2009 5:03 am ] |
| Post subject: | |
Depending on pricing and my finances at the deal time, I would be interested in `1 head stud set and 1 rod set. |
|
| Author: | Dart270 [ Fri Sep 25, 2009 6:01 am ] |
| Post subject: | |
I'm interested in a set of head studs, and a set of head studs for the aluminum engine. If main studs are available for the Alum engine, then those too. Lou |
|
| Author: | stonethk [ Fri Sep 25, 2009 6:22 am ] |
| Post subject: | |
I'd be in for a set of head, rod & mains...particularly the ones that allow attachment of a windage tray, I saw that Doc used these somewhere on this site but cant locate the picture. Maybe 2 of those cam button dealies as well. |
|
| Author: | gmader [ Fri Sep 25, 2009 6:57 am ] |
| Post subject: | |
I am very interested. Head studs rod bolts mains |
|
| Author: | NewLancerMan [ Fri Sep 25, 2009 8:25 am ] |
| Post subject: | |
I am in for the same as Greg: Head studs, Rod bolts and Mains |
|
| Author: | GTS225 [ Fri Sep 25, 2009 11:58 am ] |
| Post subject: | |
Pencil me in for the same.....head studs, rod bolts and mains. My budget at this time may not allow it, but it depends on the price. Roger |
|
| Author: | slant6 wonder [ Fri Sep 25, 2009 1:30 pm ] |
| Post subject: | |
I'm interested, the "works", same as above |
|
| Page 1 of 5 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|