| Slant Six Forum https://slantsix.org/forum/ |
|
| exhaust for slant six? https://slantsix.org/forum/viewtopic.php?t=41397 |
Page 1 of 1 |
| Author: | redfivexw [ Tue Aug 10, 2010 7:18 pm ] |
| Post subject: | exhaust for slant six? |
Does anyone have any recommendations for a replacement exhaust for my slant six duster? I dont want to do any major upgrades to the engine, the stock exhaust is getting a bit rusty and has a leak at the manifold. I would like a complete, single exhaust with a turbo/cherrybomb/flowmaster type muffler that is about 2 inches in diameter. Does any company make anything for the slant or does it have to be custom made? |
|
| Author: | Joshie225 [ Tue Aug 10, 2010 7:24 pm ] |
| Post subject: | |
There has been much discussion on this topic so you can search for and find plenty to read. |
|
| Author: | bcschief [ Tue Aug 10, 2010 8:15 pm ] |
| Post subject: | |
Try this link http://www.accurateltd.com/ Not cheap but at least someone makes it .Might try a older chain shop like Midas that has the old bender cards to make pipes for you. Brian |
|
| Author: | emsvitil [ Tue Aug 10, 2010 9:50 pm ] |
| Post subject: | |
2.25" before muffler, 2" after muffler. |
|
| Author: | F/6-866 [ Wed Aug 11, 2010 4:39 am ] |
| Post subject: | |
I bought a complete system for my 1971 PU from waldrons....www.waldronexhaust.com.......and it has worked well for me, mine is 2 1/4 front to back. |
|
| Author: | 66aCUDA [ Wed Aug 11, 2010 5:17 am ] |
| Post subject: | |
+1 on the 2 1/4 to muffler then 2' out. Frank |
|
| Author: | Aggressive Ted [ Wed Aug 11, 2010 12:52 pm ] |
| Post subject: | |
Ditto for me. Big difference in extra power and better numbers at cruise on the vacuum gauge. |
|
| Author: | redfivexw [ Wed Aug 11, 2010 7:13 pm ] |
| Post subject: | |
thanks for the help, i did do a search and did not find any posts that had specific systems. I like the look of the waldron's exhaust and the price is fair, not sure if it is a turbo muffer and it does not have the 2 1/4 in the front and 2 in the rear, but i am considering it. any others? |
|
| Author: | Joshie225 [ Wed Aug 11, 2010 8:18 pm ] |
| Post subject: | |
If these places are reproducing stock exhaust systems it's only going to be 1 7/8" for most /6 cars. I would step up to the 2 1/4" Accurate Ltd system or have a 2 1/4" system made up locally. |
|
| Author: | bcschief [ Wed Aug 11, 2010 8:20 pm ] |
| Post subject: | |
Try this link http://www.accurateltd.com/63-74-A-Body ... p_193.html for both stock and hp systems note you must call them for price on the hp system. But I do like the price better on your link but it does not include the hangers Brian |
|
| Author: | F/6-866 [ Thu Aug 12, 2010 4:19 am ] |
| Post subject: | |
When I ordered my system from Waldron I spoke with them by phone and asked if they could do the system in 2 1/4 and they could, I also discussed mufflers with them before deciding on a muffler. |
|
| Author: | carpdar [ Tue Aug 17, 2010 9:26 am ] |
| Post subject: | |
In highschool i Welded a prebent 2.25" pipe to a flange i cut-off an old down-pipe, fed it into a cherry bomb tucked under the drivers seat, with a side pipe coming out behind the driver's sider passenger door. It was realllllly cool sounding and a hell of a lot lighter and more amusing than my current 2.5" tail pipe which really complicated axle clearance among other things.. |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|