| Slant Six Forum https://slantsix.org/forum/ |
|
| 1964 Dart - 3 on the Tree to A833 - bellhousings the same? https://slantsix.org/forum/viewtopic.php?t=51866 |
Page 1 of 1 |
| Author: | 64DartGTinAZ [ Fri Apr 26, 2013 10:59 pm ] |
| Post subject: | 1964 Dart - 3 on the Tree to A833 - bellhousings the same? |
Howdy, I've got a 1964 Dart Wagon that's got 3 on the tree. I also have an A833 4 speed that I picked up (along with a hump, floor shift steering column, etc.). I'd like to do 3-on-the-tree to 4-on-the-floor swap. Will the A833 bolt up to the stock 3 speed bellhousing? The A833 came with a Quicktime bellhousing. Will that bolt up to the Slant 6? Can I use the same clutch/flywheel with the A833? Thanks! John |
|
| Author: | Dart270 [ Sat Apr 27, 2013 2:56 am ] |
| Post subject: | |
For that year, the BHs are almost certainly different. The early/mid 60s 3spds had a dedicated BH. You can crawl under and check. The 833 pattern is sort of an asymmetric/oblong trapezoid, while the 3spd is more a rounded off square. Make a few ruler measurements of your 833 at the front face and compare with the BH in the car. 833 BHs are not too hard to find. Lou |
|
| Author: | DusterIdiot [ Sat Apr 27, 2013 7:44 am ] |
| Post subject: | Yes, no, maybe... |
Quote: Will the A833 bolt up to the stock 3 speed bellhousing?
Lou is correct.The A833 came with a Quicktime bellhousing. Will that bolt up to the Slant 6? Can I use the same clutch/flywheel with the A833? You will keep the clutch and flywheel and Z-bar and linkage, TOB and clutch fork. The 3 spd bellhousing will not accept the 4 speed for those years (up to 1974). You will have to check the quicktime bell to see if the pattern is the same as your 3 spd bell (if so then you can use it). OD 4spd bellhousings are the easiest to get, on this side of the continent the 4.8"IBR 4 speed bellhousings are getting hard to find, they may be easier other areas of the US. (If going to an A-833OD I have a couple of bells I could part with.) Good luck, it's a worth while change. -D.Idiot |
|
| Author: | 64DartGTinAZ [ Sat Apr 27, 2013 7:51 am ] |
| Post subject: | |
Thanks guys! One more that I think I know the answer to, but... Is the A833 compatible bellhousing specific to the Slant 6, or will a bellhousing for a small block bolt up to the Slant 6 engine? I think I need a Slant 6 specific 4 speed bellhousing, right? Thanks again! John |
|
| Author: | sandy in BC [ Sat Apr 27, 2013 8:40 am ] |
| Post subject: | |
You need a slantrsix specific bell. What pattern is the QT bell? You may be able to leverage the QT bell to get a slant bell.... |
|
| Author: | 64DartGTinAZ [ Sat Apr 27, 2013 9:11 am ] |
| Post subject: | |
The Quicktime is for a Small Block Update - not Quicktime - it's a Lakewood...been a while since I looked at it... Thanks, John |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|