Slant Six Forum :: slant six brackets

The bracket is different, but manual super sixes are as rare as original hemi's, I can say in the car application, the auto bracket into a manual car acc. pedal application work fine just remove the kickdown pivot and your install will be complete.

-D.Idiot

to adapt a Holley 2280,, I used late 70's v8 mopar throttle cable,,
may have been off a Mirada?

much shorter than the OE 1983 D-150 cable and fit fine.

Ok I was not aware that a throttle cable needed to be changed as well?

Quote:

Ok I was not aware that a throttle cable needed to be changed as well?

On the cars the throttle cable is short like the 318/360 acc. cable... looks like that holds up as well for trucks....

Author:	1930 [ Tue Jan 14, 2014 2:58 am ]
Post subject:	slant six brackets
Can someone here confirm these brackets are the factory parts needed to make the super six set-up work on my truck. I only have ( actually still waiting too arrive ) the intake/exhaust manifold, carb and air cleaner at this point. I have a manual trans. I can see the kickdown in the picture for the automatic, was there a different bracket for manual trans that did not have the extra provision for manual trans vehicle? Thanks

Author:	DusterIdiot [ Tue Jan 14, 2014 6:26 am ]
Post subject:	Yep...
The bracket is different, but manual super sixes are as rare as original hemi's, I can say in the car application, the auto bracket into a manual car acc. pedal application work fine just remove the kickdown pivot and your install will be complete. -D.Idiot

Author:	1930 [ Tue Jan 14, 2014 11:23 am ]
Post subject:	Re: Yep...
Quote: The bracket is different, but manual super sixes are as rare as original hemi's, I can say in the car application, the auto bracket into a manual car acc. pedal application work fine just remove the kickdown pivot and your install will be complete. -D.Idiot Ok thanks, now to find one

Author:	DadTruck [ Tue Jan 14, 2014 11:34 am ]
Post subject:
to adapt a Holley 2280,, I used late 70's v8 mopar throttle cable,, may have been off a Mirada? much shorter than the OE 1983 D-150 cable and fit fine.

Author:	1930 [ Tue Jan 14, 2014 3:33 pm ]
Post subject:
Quote: to adapt a Holley 2280,, I used late 70's v8 mopar throttle cable,, may have been off a Mirada? much shorter than the OE 1983 D-150 cable and fit fine. Ok I was not aware that a throttle cable needed to be changed as well?

Slant Six Forum https://slantsix.org/forum/

slant six brackets https://slantsix.org/forum/viewtopic.php?t=54317	Page 1 of 1

Author:	DusterIdiot [ Tue Jan 14, 2014 3:38 pm ]
Post subject:	Yep.
Quote: Ok I was not aware that a throttle cable needed to be changed as well? On the cars the throttle cable is short like the 318/360 acc. cable... looks like that holds up as well for trucks....

Author:	1930 [ Tue Jan 14, 2014 4:48 pm ]
Post subject:	Re: Yep.
Quote: Quote: Ok I was not aware that a throttle cable needed to be changed as well? On the cars the throttle cable is short like the 318/360 acc. cable... looks like that holds up as well for trucks.... Ok will check it out after I get the linkage parts, thanks

Author:	1930 [ Wed Jan 15, 2014 2:41 am ]
Post subject:
Somebody offered me this linkage ( for a price ) it is different than what I have already pictured. They say Super six linkage, surely there could not have been more than one version or maybe there was a truck and auto?

Page 1 of 1	All times are UTC-08:00
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/