Slant Six Forum
https://slantsix.org/forum/

New Slant Article - Mopar Muscle
https://slantsix.org/forum/viewtopic.php?t=64070		 Page 1 of 2
Author:  Badvert65 [ Tue Sep 17, 2019 6:20 am ]
Post subject:  New Slant Article - Mopar Muscle
Mopar Muscle, December 2019. Making Slant Six Sense: Part 3.
They port and shave the head. The porting job looks great. Lot of time and money to bring compression 'up to' 8.2:1 (and ported with stock valves). Still, an interesting read.
Author:  GTS225 [ Tue Sep 17, 2019 1:25 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
Quote:
Mopar Muscle, December 2019. Making Slant Six Sense: Part 3.
Lot of time and money to bring compression 'up to' 8.2:1 (and ported with stock valves).
************************************************************************

This must be a continuance of an article they started and never finished, about a year ago. The above must be a misprint, as the stock compression is rated at 8.2:1.

Roger
Author:  jcc [ Tue Sep 17, 2019 5:39 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
Changing "to" to "from" would make more sense?
Author:  Badvert65 [ Tue Sep 17, 2019 6:25 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
Compression was measured at 7.2:1 before any work was done.
You need to read the article.
Jus sayin.....
Author:  slantzilla [ Tue Sep 17, 2019 6:36 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
Manufacturing tolerances were pretty loose on Slants. You were lucky if you got one that had 8:1.
Author:  Greg Ondayko [ Wed Sep 18, 2019 3:22 am ]
Post subject:  Re: New Slant Article - Mopar Muscle
Cool stuff. They mention Doc's book.

Not any more info than you could get here however.

Greg
Author:  jcc [ Wed Sep 18, 2019 10:47 am ]
Post subject:  Re: New Slant Article - Mopar Muscle
Quote:
Compression was measured at 7.2:1 before any work was done.
You need to read the article.
Jus sayin.....
Should i have also measured the CR myself to be certain? :D
Author:  Rug_Trucker [ Sun Sep 29, 2019 10:14 am ]
Post subject:  Re: New Slant Article - Mopar Muscle
linkie por flavor?
Author:  hank2 [ Mon Sep 30, 2019 11:19 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
https://www.hotrod.com/articles/making- ... se-part-3/
Author:  Killer6 [ Thu Oct 03, 2019 4:56 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
LOL!!! 231cfm @ .500" stock?!?!?!? Me thinkies they were a tad v-8 ified....131(& that's extremely generously gifted) is more like it....& carried over to the ported column as well..... :roll:
Author:  hyper_pak [ Thu Oct 03, 2019 5:01 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
I thought it was well written, good pictures and good details of the work performed.
Author:  slantzilla [ Thu Oct 03, 2019 6:38 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
In the classic words of Mike Jeffrey, "put a spark plug in the hole and try it again".

:roll:
Author:  csheehy [ Fri Oct 04, 2019 9:05 am ]
Post subject:  Re: New Slant Article - Mopar Muscle
Perhaps I'm alone, but I get the impression that pre-planning was non-existent. They punt the entire field.
Author:  wjajr [ Fri Oct 04, 2019 10:21 am ]
Post subject:  Re: New Slant Article - Mopar Muscle
Got the issue a week or so ago, and wondered why I couldn't recall the first two installments of a 225 performance rebuild. So the first two installments were from a year ago? I just started getting the magazine, this makes the third issue received, Mrs wjajr purchased it and others from the grand kids school fund raiser. Interesting stuff, including Mark Worman's diatribe.
Author:  Rick Covalt [ Fri Oct 04, 2019 2:14 pm ]
Post subject:  Re: New Slant Article - Mopar Muscle
Quote:
In the classic words of Mike Jeffrey, "put a spark plug in the hole and try it again".


That is 40CFM more than my Jeffrey head. They may skip right over the 12's and go into 11's!!! :D :D :D
Page 1 of 2 All times are UTC-07:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/