Slant Six Forum https://slantsix.org/forum/ |
|
Want to send my slant head out this week https://slantsix.org/forum/viewtopic.php?t=6935 |
Page 1 of 2 |
Author: | Pyper6970 [ Wed Sep 17, 2003 12:17 pm ] |
Post subject: | Want to send my slant head out this week |
Any information will be greatly appreciated, and part numbers too I have a stock head on my slant, the last missing piece to make this motor come alive. I have a .436 lift cam, 4bbl offy intake with a 390 cfm holley. Stock sizes on the head 1.62/1.36. What I wanna do is send it out to the head shop and get the head milled .060, have it pocket ported and polished, bowls blended, 3 angle with hardened seats installed. I want 11/32" bowtie valve guides, 11/32" valves. Dont wanna get too radical off baseline but I'm looking at maybe putting stock OR 1.75/1.40. I already have the Manley valve guide part number (great place to start eh?) Looking at putting stainless 11/32" valves for better airflow and head design. All opinions, comments, and .02 cents welcome. Be as brutal as you want. |
Author: | Bruce Johnson [ Wed Sep 17, 2003 12:45 pm ] |
Post subject: | |
Where are you I have a head you my be intrested Bruce J |
Author: | Pyper6970 [ Wed Sep 17, 2003 2:59 pm ] |
Post subject: | cyl head |
Los Angeles |
Author: | mighty mouse 63 [ Wed Sep 17, 2003 3:24 pm ] |
Post subject: | |
LAs a big city, where in particular are you located?....Dave |
Author: | Pyper6970 [ Wed Sep 17, 2003 3:30 pm ] |
Post subject: | La |
Torrance |
Author: | Bruce Johnson [ Wed Sep 17, 2003 3:32 pm ] |
Post subject: | |
too bad, the reason I asked was I just had one done up here with sb ford and sb chev valves and I happen to have another mildly ported head with stock valves and .060 already milled off ,it that won't work with the stroker engine I'm building |
Author: | mighty mouse 63 [ Wed Sep 17, 2003 3:36 pm ] |
Post subject: | |
Bruce how much to get that off you? Sounds like just the ticket to keep my comps 264s cam company....Dave |
Author: | Pyper6970 [ Wed Sep 17, 2003 3:40 pm ] |
Post subject: | head |
Bruce j. Do you have part numbers for the chevy and ford valves? |
Author: | mighty mouse 63 [ Wed Sep 17, 2003 4:27 pm ] |
Post subject: | |
Torrance, i'm in Lawndale. Have you checked with Valios on MB blvd. just west of Hawthorne blvd? They did a good stock job for me and can do more advanced work . Theres a second one near Downtown. Would have to look his info up. Think he's off MLK and the harbor frwy that all the magazines use for their head work....Dave |
Author: | Pyper6970 [ Wed Sep 17, 2003 5:10 pm ] |
Post subject: | head |
GT63....we are neighbors wow. Yes I had Vellios do the head way back when completely stock. Now its time for modified competition. Vellios is good for one thing....stock....thats it. They have a good crank polishing setup Rumor has it they had a kid JB weld a cylinder and hone it. Harry and Devon are cool machinists. but.......nah. What kinda ride ya got? Seen me running around? |
Author: | mighty mouse 63 [ Wed Sep 17, 2003 5:51 pm ] |
Post subject: | |
Those two are good, Watch out for the other guys and under no circumstances let them near your block, unless you want to pay a competent shop to correct their mistakes. Got some firsthand horror stories about that place. Must admit did a good stock job on the heads, but would only let the Harry do the work. Will get you the name and address of the place in LA when I get off duty and have access to the materials. How I have missed your beast is beyond me, definitely gets your attention as for myself got a 63 GT Dart brown in color That looks dead stock down to the soon to be replaced 13 wheels. As for that JB weld cylinder job, my brother-in-law had two cylinder walls fail on his GTO equiped 389 3 months after they rebuilt and sleeved it. Gives on something to think about...Dave |
Author: | mighty mouse 63 [ Thu Sep 18, 2003 10:14 am ] |
Post subject: | Leads |
Theses two come highly recommended BPE RACING HEAD 714-572-6072 or WWW.BPEHEADS.COM located in Placentia.......CYLINDER HEAD SPECIALIST 800-346-8075 or 714-578-1133 located in Fullerton..Dave |
Author: | Pyper6970 [ Thu Sep 18, 2003 3:11 pm ] |
Post subject: | leads |
Called up BPE...Steve seems to be very knowledgable with the slants. As for Cylinder head Specialists, they went out of business and California Head Specialties took over, he doesnt seem to know much about anything except stock applications, he evens sends out the porting work to another place. So far BPE might be getting it. Thanks for the help dave Pete |
Author: | mighty mouse 63 [ Thu Sep 18, 2003 3:38 pm ] |
Post subject: | |
Did you review their price list? They have a stage I,II,III porting option. Thought the prices reasonable. BTW their stage II is 75 bucks more then the basic stock job Vallios did! |
Author: | Bruce Johnson [ Thu Sep 18, 2003 10:35 pm ] |
Post subject: | |
I'm picking up my head tommorow to blend in after the seats. I'll get the part #s for the valves and the springs, the last head I had them do used EGGE valves as in the slant sickness artical, this time I saved a little and got slightly larger valves, as for the other head shipping really cuts in to what I can get for it, I think the best advice I can give is learn to port, then plan to spend about $ 550 for the machining, valves, seats guides, springs,retainers, locks. I should mention that this engine is planed to be a 170 with a 198 crank and pistons with a 3.5" bore. but for everyone who hits on this post; 40 hours of porting and $500 to $600 into the head is the best time/money spent on this "Economy" mill. It was never intended to be a race engine but getting the head ready for the cam and a 600 cfm carb will raise allot of questions Bruce J. |
Page 1 of 2 | All times are UTC-08:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |