Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Tue Nov 26, 2024 12:31 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 9 posts ] 
Author Message
PostPosted: Fri May 05, 2006 2:58 pm 
Offline
4 BBL ''Hyper-Pak''

Joined: Wed May 03, 2006 12:41 pm
Posts: 29
Car Model:
I have a '64 Valiant convertible, plain-jane six, no plans for hi-po.

The OEM rear leafs are flattened-out; if I put two people in the back seat, the rear springs are bottomed-out, and we scrape bottom a lot...

Am looking at ESPO springs&things, and they offer "four-leaf" and "five-leaf"....

Are four-leaf springs just going to flatten-out again, and if so, how quickly...

If I go five-leaves, how will that impact the ride quality of the car ?


Not looking to go crazy with suspension upgrades, but want to make a wise choice for the "long haul"...

Thanks for your suggestions...


Frank McMullen


Top
   
PostPosted: Fri May 05, 2006 7:03 pm 
Offline
Turbo Slant 6
User avatar

Joined: Tue May 02, 2006 12:16 am
Posts: 708
Location: Ooltewah, Tennessee
Car Model:
Quote:
The OEM rear leafs are flattened-out; if I put two people in the back seat, the rear springs are bottomed-out, and we scrape bottom a lot...

Not looking to go crazy with suspension upgrades, but want to make a wise choice for the "long haul"...

Frank McMullen
I had a situation exactly like that only different ;-) I've been pleased with the air adjustable shocks I got from, as I recall, Pep Boys. When I know the load will go up I push the air pressure up. :-)


Top
   
 Post subject:
PostPosted: Fri May 05, 2006 7:54 pm 
Offline
Supercharged
User avatar

Joined: Mon Sep 26, 2005 5:09 pm
Posts: 2946
Location: Gilbert, Arizona
Car Model: 1962 Plymouth Valiant Signet
Air shocks are a bad idea on a Mopar A-body. The upper shock mounts are not designed or built to handle the stresses and will tear out of the floor pan. Same deal with coil-overs.

_________________
David Kight
'62 Valiant Signet, White
'98 Dodge Dakota
'06 Jeep Liberty

Growing older is unavoidable but growing up is strictly optional.


Top
   
 Post subject:
PostPosted: Sat May 06, 2006 1:14 pm 
Offline
EFI Slant 6
User avatar

Joined: Thu Aug 12, 2004 9:21 pm
Posts: 297
Location: San Diego
Car Model:
i swapped in a leave from a 91 toyota pickup in to my leaf pack and picked up the rear end 1" to 1 1/2" and firmed up the ride some but not too much. load capacity went up but not much. i think i still need to get new springs.

zedpapa

_________________
1970 dodge dart w/225 /6 bored .040" over, holley 390cfm w/vac. sec., compcams 252s, clifford shorty headers w/2.5" exhaust w/flowmaster, f-body 11" front discs, aluminum A-833OD, 8 1/4 w/3.21 SG
soon to have 5 gears!!!


Top
   
 Post subject:
PostPosted: Mon May 08, 2006 8:24 am 
Offline
4 BBL ''Hyper-Pak''

Joined: Wed May 03, 2006 12:41 pm
Posts: 29
Car Model:
Just did the air-shock thing on my '60 Windsor....

I 'm thinking that I'll go for the five leaves in the Valiant, and throw some sand-bags in the trunk if it sits too high...

My fear with the four-leaf pack is that they'll sag right out, just like the originals...

Any of you life-long A-body folks remember how long it took these cars to sag back in the day ?


Thanks,

Frank McMullen


Top
   
 Post subject: Get the 4-leaf springs
PostPosted: Tue May 09, 2006 10:00 am 
Offline
EFI Slant 6

Joined: Sat Sep 13, 2003 9:45 pm
Posts: 446
Car Model:
I'm going to be a maverick and post something that has something to do with "4 leaf vs. 5 leaf".
I have a 63 Valiant and I just installed 5-leaf JC Whitney springs a few weeks ago. Pretty plain car - no racing ambitions.

I adjusted the torsion bars 1/8" higher than service manual recommends and the rear was still jacked-up .

Now I'm making new front brackets to raise the front eye so that the rear sits lower (to compensate for the springs).

I wish I had gotten the 4-leaf springs.

They will make your car sit right - but will they sag soon?

You can take apart the old springs and keep the top leaf as insurance.
If the new springs sag a year or two from now, you can cut the extra leaf to be between the 3rd and 4th leaves in length and make your own 5-leaf.


Top
   
 Post subject:
PostPosted: Tue May 09, 2006 4:01 pm 
Offline
Board Sponsor
User avatar

Joined: Wed Oct 23, 2002 8:48 pm
Posts: 366
Location: Southeastern PA
Car Model:
I have six-leaf springs on my '68 Dart, and I think it sits very close to what I would *imagine* the stock ride height would be. I think it is not always the number of leaves, but rather the arch of the springs. Also, I do think leaf springs settle a little, I wouldn't say sag, but I think the suspension will settle a little once it is driven.

I have the front ride height set how the factory service manual says, and with the leaf springs I have, the bottom of the rocker panel is dead level.

_________________
'68 Dodge Dart 4dr Sedan
Image


Top
   
 Post subject:
PostPosted: Tue May 09, 2006 5:49 pm 
Offline
EFI Slant 6

Joined: Sat Sep 13, 2003 9:45 pm
Posts: 446
Car Model:
I dunno why those work for you. Are yours ESPO?
The 68 Dart is not much heavier than a 64 conv Valiant.

I was asking this forum a similar question a month ago and no one made a strong case for the 4-leaf springs.
I bought the 5-leaf ones.
As I understand it, the question is "should I put standard springs or heavy-duty springs on a (63 or) 64 Valiant?"
In my (recent) experience, the HD springs are too heavy-duty for a 63 hardtop Valiant.


Here are some others' thoughts:

[Note: this was advice to someone with a 65 Valiant V-200]
Quote:
Mike,

I have the JCWhitney 5 leaf HD springs in both my cars (both sets about 10 years old and still fine). They are perfect for my heavier '68, but a bit stiff for the '64. Even with no rear SwBar, the '64 oversteers just a touch, but is neutral with a passenger in the rear seat. You might just get the JCW 4-leaf standard replacements. Good quality springs, and hard to beat the price. Course, the 5-leafs are just a bit more and you can always remove a leaf. You might also check out the adjustable front perches from www.arengineering.com. You will need to drill the holes on your stock perches to 5/8" if you use those - no biggie. I also recommend polyU bushings (Energy Susp or PST brand so they don't squeak as much, although still a little), if you want least flex and best handling. Ride is slightly harsher, but not a big deal.

I plan on trying my current 5 leafs with the lowest leaf removed to see how that goes. Eventually, I will buy some fiberglass leafs from http://www.flex-a-form.com/ to shave about 35-45 lbs off - mostly unsprung weight too!

Cheers,

Lou
Quote:
4-leaf: Standard
5-leaf: HD and wagon
6-leaf: XHD (HD Wagon)

All varieties are readily available new, e.g. from Espo.


Last edited by sixsignet on Tue May 09, 2006 6:36 pm, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Tue May 09, 2006 6:34 pm 
Offline
Board Sponsor
User avatar

Joined: Wed Oct 23, 2002 8:48 pm
Posts: 366
Location: Southeastern PA
Car Model:
Yep. I got them a few years ago (actually, 2001, I think) from ESPO at the Chrysler show at Carlisle. I remember they asked me if I wanted "1 inch higher or stock ride height?" I went with stock ride height.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 9 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited