Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 10:29 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 9 posts ] 
Author Message
 Post subject: hose inlet
PostPosted: Tue Apr 15, 2008 8:17 pm 
Offline
4 BBL ''Hyper-Pak''

Joined: Tue Nov 13, 2007 9:59 pm
Posts: 41
Location: nola
Car Model:
thru the search i was able to answer some of my cooling questions - (such as no longer able to buy rad hoses with springs) - i need to replace the inlet metal pieces for the heater hoses on the engine block - i did not come up with much in search because i am sure i am not using correct term - anyways where can i purchase these? - thank you - oo3

_________________
69 a100 225 tree3


Top
   
 Post subject:
PostPosted: Tue Apr 15, 2008 8:44 pm 
Offline
Site Admin
User avatar

Joined: Mon Mar 31, 2003 1:04 pm
Posts: 7471
Location: Oregon
Car Model: 2023 Eichman Digger?
Your local parts store has them. You want the 5/8" ones.

CJ

_________________
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Tue Apr 15, 2008 8:57 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
Later model cars have two different size heater hose fittings. Look at the heater hoses and see if they are both 5/8" or if one is 1/2", but if you're speaking of your '66 A100 they will both be 5/8"

_________________
Joshua


Top
   
 Post subject:
PostPosted: Fri Apr 18, 2008 12:33 am 
Offline
4 BBL ''Hyper-Pak''

Joined: Tue Nov 13, 2007 9:59 pm
Posts: 41
Location: nola
Car Model:
not having succes removing the nipple yet - tried penetrating oil and visegrips - applying heat and cooling multiple times - has not broken off yet but wont budge - what next? - oo3

_________________
69 a100 225 tree3


Top
   
 Post subject:
PostPosted: Fri Apr 18, 2008 1:39 am 
Offline
Turbo Slant 6

Joined: Thu Jul 13, 2006 8:05 pm
Posts: 770
Car Model:
Take a hammer and start taping it lightly, tap in adirection like you was trying to drive a nail. Dont get to hard with because your not trying to beat it loose really, all your doing is jarring the threads so that the penitation oil can, well, penitrate. Use the hammer in a way that it kinda just bounces back off and do this for 20 or 30 times ( striking the hammer). AFter you use the hammer spray with oil and let set a hour. Then repeat doing the same thing. Let set a hour again, then repeat again. After about four rounds of this then try with your vise crips try working the pipe back and forth. If its not coming loose start with the hammer and oil again. Sooner or later it will start moving, just dont get in a hurry and let the vibration from the hammer strikes and the oil do there job.


Jess


Top
   
 Post subject: Regarding stuck inlet
PostPosted: Fri Apr 18, 2008 5:06 am 
Offline
TBI Slant 6

Joined: Wed Feb 20, 2008 5:38 am
Posts: 202
Location: Medical Lake, WA
Car Model:
Do you have to drive the car? If not perhaps you can goop on some Naval Jelly for a few hours and dissolve the external rust. Hose it off when finished and reapply--do the light tapping with the hammer thing (as previously described) and walk away for a few hours. Hose off and re-apply/do over. Hose it off after another few hours. Douse with various flavors of penetrate--I did this for 3 days and that things spun right out. Be patient if you can be...penetrating oils really do work if they are applied in quantity and given time to do their magic. Good luck!

_________________
Slanted D150


Top
   
 Post subject:
PostPosted: Fri Apr 18, 2008 10:18 am 
Offline
4 BBL ''Hyper-Pak''

Joined: Tue Nov 13, 2007 9:59 pm
Posts: 41
Location: nola
Car Model:
i actually did a little of the hammer bit but not to that extant - will do more over the weekend - i dont have to drive the van any time soon - while i have things apart i will also bring the radiator to a shop for check out - replace the water pump and timing set - have not had cooling problems but this being a van i want to make sure everything is well as they seem to be more prone to such conditions - and they are also a little more of a pain to work on than the cars - thanks - oo3

_________________
69 a100 225 tree3


Top
   
 Post subject:
PostPosted: Sat Apr 19, 2008 5:33 pm 
Offline
4 BBL ''Hyper-Pak''

Joined: Tue Nov 13, 2007 9:59 pm
Posts: 41
Location: nola
Car Model:
like they said take your time and its out - i also ended up using a pipe wrench as the vise grips just kept slipping - thanks - oo3

_________________
69 a100 225 tree3


Top
   
 Post subject: hosed...
PostPosted: Sun Apr 20, 2008 7:41 pm 
Offline
TBI Slant 6

Joined: Wed Feb 20, 2008 5:38 am
Posts: 202
Location: Medical Lake, WA
Car Model:
Pipe wrench for a pipe...seems fitting...

_________________
Slanted D150


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 9 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Google [Bot] and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited