What will swap with the stock Slant water neck??


I want to get one that is "Straight Out" rather than the stock / factrory 90* angle.


Lou, I am getting that summit crossflow for ruster, like you have in the '64 What did you use? (for a water neck?)

I need the straight up water neck to route the upper rad hose to the left side of the engine bay.( for the crassflow rad.)

I need a similar one to get the thing (ruster) running.

I am looking for one on summit now, but there's a lot to choose from.

I have busted 2 older Rads putting on my electric fan, so it's time to upgrade. I was going to get this rad anyway...so might as well spend the dime now.


Thanks all sages for you help!


Greg

_________________
http://www.youtube.com/hyperpack

Would the one from a 318 fit??

_________________
Part of Tyrde-Browne Racing

Or a 440?

_________________
50 chrysler,54 Plymouth, 64 Valiant conv 4 speed, 66 Valiant V8 wagon, 70 Challenger R/T 440+6 conv 4 speed,80 Colt, 98 Neon ACR,84 Honda V45 Magna
Taking care of 57 300C conv,48 T&C conv. Missing my 67 GTX and 36 Ply coupe

The 318 and 440 are the same but the slant takes a smaller T- stat(diameter). Now I don't know what year they changed the small block late model intake but it may be a match for the size of the slant. They are smaller and are stamped steel.May work.

Would This work?
http://summitracing.com/parts/DCC-44520 ... refilter=0

it's for the 1979- 93 Small blocks.

My main concern is the Bolt holes lining up and of course the t'stat Registereing in the housing correctly.


Greg

_________________
http://www.youtube.com/hyperpack

You could check around a see which engines use the same thermostat gasket-that would let you know what fits.

_________________
50 chrysler,54 Plymouth, 64 Valiant conv 4 speed, 66 Valiant V8 wagon, 70 Challenger R/T 440+6 conv 4 speed,80 Colt, 98 Neon ACR,84 Honda V45 Magna
Taking care of 57 300C conv,48 T&C conv. Missing my 67 GTX and 36 Ply coupe

Thanks!


Yep 79 and newer LA Engines are the same as the slant.

78 and older are the bigger 2 1/4 T-stat Housing.


Greg

_________________
http://www.youtube.com/hyperpack

Greg
PM me if this works well as I have the same needs.
Thanks,
Frank

_________________
Scrapple: Because a mind is a terrible thing to waste.
73 Duster - Race Car
66 Dart Wagon - DD
178" FED
82 D150
All Slant powered

I bought one at Summit that was supposed to fit the '79 and later bb, but the hole spacing was still too wide. From what I could tell, none of those sold at Summit have the correct hole spacing for a /6. Someone had mentioned in an earlier post a chrome one from Mopar Performance that is supposed to fit, but I haven't located it yet.

Moose

_________________
1966 Clark Cortez, Industrial /6

the 79 up small block chrome one from mopar is #P4452025 stamped steel.

I went to Pick a part and just kept looking till I found what I needed,pulled mine off a Ford.Didnt pay attention to what model or year,know it had a big heavy hood cause it came down on my head and put me on the ground.Guzzi Mark

Yep, '79 up Mopar SB V8 is the one I have.

Lou

_________________
Home of Slant6-powered fun machines since 1988

yup Summit charges a hefty price for the thing, but it fits.

The holes are 5/16" on the stamped piece.


I just drilled them out to 3?8" for the slant.

Will work fine.

Probably one from a boneyard LA engine post 79 will work for a lot cheaper!


Greg

_________________
http://www.youtube.com/hyperpack

I have to dig around the garage for some comparison but a 2.2/2.5 4cylinder style out let may work. nico