Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 08, 2024 12:34 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 18 posts ]  Go to page 1 2 Next
Author Message
PostPosted: Mon May 24, 2010 10:16 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Okay so my cousin is set on getting herself a Mopar. We went and looked at Vera's twin yesterday. 1965 Dart 270 225 and the lovely 1920 Holley.
The biggest issue with this car is the missing freeze plug on top of the engine block. Now, my question is this: can this be replaced without the engine being pulled?? I've searched the forum and haven't found a definitive answer on this....

Thanks everyone! :)

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 10:26 am 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13046
Location: Fircrest, WA
Car Model: 76 D100
The freeze plugs on the driver's side of the block, buried under the manifolds. Is this what you mean by the plug being on the "top" of the block?

If so, you just need access to pull the old plug out, with a pair of pliers, clean the edges of the hole, and pound a new plug in. If you can do that without pulling the manifolds, then you are fine.


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 10:32 am 
Offline
Guru
User avatar

Joined: Mon Oct 14, 2002 4:32 pm
Posts: 4880
Location: Working in Silicon Valley, USA
Car Model:
On the early engine blocks, the center (of 3) freeze plugs is hard to access without removing the manifolds.
I have been able to install a "temporary" bolt-in freeze plug into that location, with-out pulling the manifold set, but it is not a real "fun" job.
DD

Image


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 10:32 am 
Offline
EFI Slant 6
User avatar

Joined: Tue Mar 16, 2010 8:41 pm
Posts: 265
Location: Houston
Car Model:
The biggest issue with replacing freeze plugs is usually having good access to the location.

The mating surfaces must be very clean and smooth and you've got to have some room to swing something (preferably something like a rubber dead blow mallet) in such a manner that you can evenly drive in the plug.

_________________
1954 Ford, Tudor Mainline
1976 Plymouth Valiant, 4 door

Image
www.automotive-ninja.com


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 10:44 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Reed-Yes, exactly the spot.

I'm not sure about the clearance or how easily I will be able to access the spot....apparently I won't have to pull the old one as it is missing. What kind of problem might that pose?

The motor in this car sounds AMAZING. I should have taken video. She doesn't even need a valve lash...

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 11:00 am 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13046
Location: Fircrest, WA
Car Model: 76 D100
Well, again, WHY is it missing? Did the engine get cold enough for the coolant to freeze and pop out the plug? If not, why was the plug able to pop out? Corrosion in the water jacket? Cracked head making too much pressure in the block (although this would likely cause the radiator cap to open before the freeze plug came out)?

Doc's solution of the expanding freeze plug is probably your best bet for a quick and dirty repair. I would try and find out why that freeze plug is no longer in the block before buying the car.


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 11:06 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Thank you Reed. I will definitely make sure and ask. :)

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 11:22 am 
Offline
Guru
User avatar

Joined: Mon Oct 14, 2002 4:32 pm
Posts: 4880
Location: Working in Silicon Valley, USA
Car Model:
I can think of a few reasons on why the plug is missing:

- The plug was leaking, was removed for repair and the owner / mechanic could not get the replecement plug reinstalled.

- The plug was incorrectly installed and came-out under cooling system pressure.

- The block water froze and pushed-out the plug.

-There is a crack in the block intersecting the plug's hole, this makes it near impossable to hold a pressed-in metal expansion plug.
DD


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 11:25 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
No visible cracks. At all. Anywhere. This motor is in nice shape. I'm uploading pics now to photobucket...will post the few I took.

I'm kinda jealous! She's so purty!

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 11:58 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Okay so here's the deal: dude started the car after she had sat all winter. He noticed fluid leaking (saw steam from under the hood, shut car off and checked under hood) and noticed a pin hole in the freeze plug seal(?)the fluid in the block HAD frozen. SO. Again I ask What kind of problems could this lead to? is this car going to be worth it? Does it mean there may be internal issues due to the frozen block? No cracks are visible....NAPA carries a universal plug now. Plug is NOT missing, just faulty? Screwed up from the freeze?

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Mon May 24, 2010 2:37 pm 
Offline
Turbo Slant 6

Joined: Fri Feb 06, 2004 9:47 pm
Posts: 526
Car Model:
Rusted out. So you're safe, just get care of all the core plugs.

Cheers, Wizard


Top
   
 Post subject:
PostPosted: Tue May 25, 2010 5:14 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8684
Location: Silver Springs, Fl.
Car Model:
The other thing I would be cautious about. You said the engine sounds "awsome". How long has the engine been run with no coolant in the block/head?

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Tue May 25, 2010 9:59 pm 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Actually, dude lost his liscence and hasn't been driving the car for quite some time. Selling her for court costs....

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
 Post subject:
PostPosted: Tue May 25, 2010 10:17 pm 
Offline
Board Sponsor
User avatar

Joined: Fri Feb 29, 2008 10:49 pm
Posts: 1547
Location: Salem, Oregon
Car Model: 1984 D100 Shorty Custom
Well, fill it with your antifreeze/water mix, pour some gas in her, and let it run for awhile, get up to operating temp.

Once you get there, shut it off, and check on it as it cools. Make sure there are no leaks, and sniff around a bit, see if you smell any coolant. Once it has cooled off, run her back up to operating temp again. Do it a few times if possible. Multiple heat cycles may show a crack that you wouldn't have seen before.

Also, keep a keen eye on the dipstick, make sure that there is nothing but oil on it. Same with radiator, coolant only.

Example:

I have an engine block sitting in the shop that is from a '65 as well. You wouldn't know by looking at it, but there is a 3" long crack running the length of the block on the driver side, about 3" up from the dipstick tube. Would only leak after being warmed up, and then shut off.

I still need to get that fixed....

Where are those pics! I wanna see!

:mrgreen:

~THOR~

_________________
1984 D100 Shorty Custom
Certified Auto Appraiser - RevItUp Classic Appraisals
President - Cherry City Bombers CC
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Wed May 26, 2010 9:57 am 
Offline
TBI Slant 6
User avatar

Joined: Sun Oct 12, 2008 5:48 pm
Posts: 229
Location: Portland, OR
Car Model:
Ahh the dipstick.....I did check it, it needs to be replaced, but there was only oil...and clean oil, I might add. Did not pop the radiator cap. The damn radiator is nice! I'm thinking she is going to go ahead on this....but I will definitely do the afore mentioned things first.

Let's see if I can do this right pics wise.....This is Stella.
Image

_________________
"Vera" 1965 Dart 270
Because good girls love being dirty!!


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 18 posts ]  Go to page 1 2 Next

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited