Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Wed Nov 18, 2026 11:51 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 14 posts ] 
Author Message
 Post subject: woah!!!!
PostPosted: Mon Aug 18, 2003 3:22 pm 
I just found out i have no crankshaft puley bolt! what should i do?is this a big problem???HELP!!! :cry:


Top
   
 Post subject:
PostPosted: Mon Aug 18, 2003 3:33 pm 
Offline
Board Sponsor
User avatar

Joined: Thu Oct 24, 2002 3:54 pm
Posts: 191
Location: Atlanta, Ga
Car Model:
Lot's of Slants didn't come with them. I added one to my '65 so that I could turn it over easier when timing the disributor and adjusting valves.

_________________
"Former Owner" of '65 Barracuda, 225, Auto, MP 2bbl intake, MP cam, Dutra Duals. Presently Moparless.


Top
   
 Post subject: No Worrys
PostPosted: Mon Aug 18, 2003 3:58 pm 
Offline
Turbo EFI
User avatar

Joined: Sun Nov 03, 2002 1:49 pm
Posts: 2445
Location: Lubbock, TX
Car Model:
Nothing to worry about. I don't have one on mine either. 8)


Top
   
 Post subject:
PostPosted: Mon Aug 18, 2003 7:50 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14980
Location: Park Forest, Illinoisy
Car Model: 78 Volare
If you really have to have one, go to a harware store and buy a 3/4 fineX1-1/4" bolt and a thick washer. :shock:

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Tue Aug 19, 2003 7:55 pm 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Thu Jun 19, 2003 5:59 pm
Posts: 46
Location: san jose, ca
Car Model:
I grabbed mine form a small block V8, same size as a slant and easier to find in the junk yard. While I recognize that it isn't needed, I couldn't figure out how to re-install my balancer without one.


Top
   
 Post subject:
PostPosted: Tue Aug 19, 2003 8:07 pm 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
There is a tool called a harmonic balancer installer, pretty much a long rod with a bearing and some washers. Off the top of my head I know mac tools has one because thats the one I used before, I'm sure you can get others for cheaper.


Top
   
 Post subject:
PostPosted: Tue Aug 19, 2003 9:04 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14980
Location: Park Forest, Illinoisy
Car Model: 78 Volare
Quote:
There is a tool called a harmonic balancer installer, pretty much a long rod with a bearing and some washers. Off the top of my head I know mac tools has one because thats the one I used before, I'm sure you can get others for cheaper.
A long 3/4 fine bolt, a nut, and a couple flat washers will work too. :shock:

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Tue Aug 19, 2003 10:27 pm 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
Slantzilla, yea, infact before I found the tool in the garage I just "carefully" banged the balancer on with a mallet, making sure I only hit it in the center. Took forever and a day but it works.


Top
   
 Post subject:
PostPosted: Wed Aug 20, 2003 12:14 am 
Offline
Guru
User avatar

Joined: Sat Oct 12, 2002 11:22 am
Posts: 3740
Location: Sonoma, Calif.
Car Model: Many Darts and a Dacuda
Quote:
Slantzilla, yea, infact before I found the tool in the garage I just "carefully" banged the balancer on with a mallet, making sure I only hit it in the center. Took forever and a day but it works.
Ouch... if you have to "bang one on", be sure to stand the engine on end so the crank's rear flange is solid to the floor, doing this keeps the shock off the #3 main bearing thrust surface.

If the engine is in the car, find a bolt or the install tool.
DD


Top
   
 Post subject:
PostPosted: Wed Aug 20, 2003 12:19 am 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
Doc, I'll keep that in mind for next time. The engine was horizontal on a stand. After the engine was installed in the car and I found the tool, I used it to make sure it was completely seated.


Top
   
 Post subject: crankshaft pully bolts
PostPosted: Fri Nov 04, 2005 7:57 pm 
Offline
2 BBL ''SuperSix''

Joined: Mon Nov 08, 2004 6:53 pm
Posts: 11
Car Model:
Long Time No See....

So, as I understand it, that hugmongus important-looking bolt (1.25inch)on the front of my engine's crankshaft is only important for turning the engine over or bolting on a harmonic balancer?

(...I just finished pulling my '87s engine and replacing it with an '84 engine...)

Does it need a torque value? How about those three little bolts that actually hold the pully on?

_________________
1987 Dodge Ram 100 Custom
Slant 6
833

...gonna keep this one...


Top
   
PostPosted: Fri Nov 04, 2005 8:14 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
So, as I understand it, that hugmongus important-looking bolt (1.25inch)on the front of my engine's crankshaft is only important for turning the engine over or bolting on a harmonic balancer?
Correct. The crankshaft pulley/vibration damper/harmonic balancer (three names, same part) is a keyed interference fit on the crank snout. It will not fall off without a bolt. As has been mentioned many (actually, most) slant-6s came from the factory without a bolt in this location. It is not necessary.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri Nov 04, 2005 8:54 pm 
Offline
4 BBL ''Hyper-Pak''

Joined: Sat Sep 03, 2005 8:05 pm
Posts: 38
Car Model:
I got into a arguement the other day with a friend when my slant was stuck...He said to simply turn it over with a powerbar on the balancer...I have three parts cars here and of the 4 slant 6's none had the bolt...He told me someone must have stolen them :roll:


Top
   
PostPosted: Sat Nov 05, 2005 8:26 pm 
Offline
2 BBL ''SuperSix''

Joined: Mon Nov 08, 2004 6:53 pm
Posts: 11
Car Model:
...huh...both my '87 and my '84 had those bolts...I torqued that bugger to 75FTLBs just in case...but lacking experience, plus the manual says nothing...I guess 20 FTLBs for those three little bolts?...you know, the ones that actually hold the pully in place?

_________________
1987 Dodge Ram 100 Custom
Slant 6
833

...gonna keep this one...


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 14 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited