Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Wed Dec 11, 2024 11:41 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 7 posts ] 
Author Message
PostPosted: Fri Jan 13, 2012 12:34 pm 
Offline
3 Deuce Weber
User avatar

Joined: Fri Nov 26, 2010 12:18 pm
Posts: 97
Location: Bolinas, California
Car Model:
I just had the head redone because the valve seats had gone bad.(original engine never converted for unleaded fuel). The Machine shop said the HEAD looked Great. They decked it and cleaned it. Now I have it all back together. I also switched from the single barrel to the double Carter bbd and the intake/exhaust manifolds as well. It has a new Carburetor, distributor, wires, starter, coil, plugs, oil....etc. Everything has been double checked- checked the points gap, correctly wired from distributor.I am getting spark. Fuel is going to the carb. Charged the battery. - It doesn't seem like it is turning over hard enough. It sometimes seems like it wants to start but nothing. No popping or anything. I cant seem to figure it out.


Top
   
 Post subject:
PostPosted: Fri Jan 13, 2012 12:58 pm 
Offline
6 Pack Dart
User avatar

Joined: Sat Nov 02, 2002 5:44 pm
Posts: 2281
Location: Eugene, Oregon
Car Model:
Check your distributer timing.

Richard

_________________
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Fri Jan 13, 2012 1:12 pm 
Offline
Guru
User avatar

Joined: Mon Oct 14, 2002 4:32 pm
Posts: 4880
Location: Working in Silicon Valley, USA
Car Model:
Check valve lash.
DD


Top
   
 Post subject:
PostPosted: Fri Jan 13, 2012 3:00 pm 
Offline
3 Deuce Weber
User avatar

Joined: Fri Nov 26, 2010 12:18 pm
Posts: 97
Location: Bolinas, California
Car Model:
i lashed the valves and it fired right up! There is some valve knocking though. I guess I have to lash them again? I am new to mechanics.


Top
   
 Post subject:
PostPosted: Fri Jan 13, 2012 5:51 pm 
Offline
3 Deuce Weber
User avatar

Joined: Fri Nov 26, 2010 12:18 pm
Posts: 97
Location: Bolinas, California
Car Model:
I was told to re-torque the head after 200 miles, is this correct? any other Break-In procedures?


Top
   
 Post subject:
PostPosted: Sun Jan 15, 2012 8:54 am 
Offline
Turbo EFI
User avatar

Joined: Wed Feb 23, 2005 1:50 pm
Posts: 2353
Location: Pertneer Nashville TN
Car Model:
Quote:
I was told to re-torque the head after 200 miles, is this correct? any other Break-In procedures?
Steel head gasket? Probably don't have one of those. The Victor and the Permatorque Blue you don't need to redo.

Run for 500 miles reset the valves, change the oil. I usually run a new engine for 20 minutes for cam break in and change the oil and filter. It catches crap from machine work.

_________________
'72 Duster 198 stock cam, 3:23's Hookers on jack stands for 8 years in the driveway
'79 Maxivan 360 Offy Qjet Comp RV cam/rusting in the driveway.
93 D350 160HP Cummins Auto :-( Dually Clubcab needs a injector pump
2005 Golden Couch Buick


Top
   
 Post subject:
PostPosted: Mon Jan 16, 2012 6:35 am 
Offline
Turbo Slant 6
User avatar

Joined: Sun Apr 24, 2005 10:26 am
Posts: 520
Location: Issaquah, WA
Car Model:
it's probably not turning over hard enough because everything is not working hard due to replacement parts (IE, everything works fine but not enough juice.) That or you had to charge the battery and it's not cranking out the amps it needs. Make sure the battery is fully charged. Get it tested at a local auto store and if needed they can give it a deep cycle charge within a few hours. Such recharge can work better than home battery chargers and will save you the energy :wink: This is a good place to start and won't cost you more than already spent.

_________________
'73 Scamp (the girlfriend): 225ci super/6 2BBL conversion (Almost done!)
'90 Subaru, wagon (the wife): H4-cyl 2.2L

1977 Mercedes-Benz 300D, 5cyl diesel(For sale!)
Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 7 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Bing [Bot] and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited