Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 6:56 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 69 posts ]  Go to page Previous 1 2 3 4 5 Next
Author Message
 Post subject:
PostPosted: Thu Nov 10, 2005 7:36 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
Autoline rebuild
I believe we've identified the problem.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:08 pm 
Offline
Board Sponsor & SL6 Racer
User avatar

Joined: Fri Nov 08, 2002 4:48 pm
Posts: 5835
Location: Burton BC canada
Car Model:
Condensor

_________________
Yeah....Im the one who destroyed this rare, vintage automobile.....

Image


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:09 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Update:

Replaced fuel pump with Crappy Tire Special, raised float level, no improvement. Still cutting out after 5 or so minutes of hard driving. Kept the car to a stumble all the way home, parked it, WOT in gear til it stumbled, shut it off. Whipped out the plugs, all are reading lean with a light dusting of white powder. Compression test: 135 all the way across.

I realise that the carb is lean, but I have a #65 jet in there. The only thing I can attribute the lean mix to is the throttle shaft bushings, they have slightly perceptible play in them, no other leaks that I can find. I have been trying to get a proper working carburetor on this engine for at least a year now. Propane, carb kleen sprayed at the intake mfld gasket all day does not change the idle. PCV looks fine. I cant understand it. There has to be more to enriching the main circuit than just swapping the jet, it has made very little difference to mine and most people are running a #62 jet. Being that as it may be, I still dont think the carb is the direct reason for this stumbling, as the car pulls smooth and strong for the first few minutes, the stumbling seems to come when the engine reaches a certain temperature. I can drive for a fair distance longer if I take it easy, maybe all day, I dont know. But as soon as I start hammering on it or take it out on the highway, the stumble comes back. There is no more backfire, but hit the gas and it will stumble.

I suspect there must be a crack between some of the exhaust and intake valves, my cousin's Pony did this same thing albeit more severe and this is what he found. But I dont know, Im exhausted. Ive thrown everything Ive got at this thing and made no difference.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Last edited by steponmebbbboom on Thu Nov 10, 2005 8:12 pm, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:10 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Quote:
Condensor
Tomorrow I will throw on a new coil and ignition kit, after that I am out of ideas. Thanks...

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:16 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Run it without the gas cap.


The tank might not be venting.

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:28 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
Quote:
I realise that the carb is lean, but I have a #65 jet in there. The only thing I can attribute the lean mix to is the throttle shaft bushings
No. Slightly-perceptible play here will not cause anywhere near the severe symptoms you're experiencing. I think your carb's power valve and/or metering block are FUBAR. Welcome to the Wonderful World of Wemanufactured CarbuWeters.
Quote:
I have been trying to get a proper working carburetor on this engine for at least a year now.
Send me a PM.
Quote:
I still dont think the carb is the direct reason for this stumbling, as the car pulls smooth and strong for the first few minutes, the stumbling seems to come when the engine reaches a certain temperature.
Choke compensates for screwed-up carburetor
Quote:
I suspect there must be a crack between some of the exhaust and intake valves
Seriously doubt.
Quote:
my cousin's Pony
I'm assuming you mean Mustang, i.e., Ford. Of course it broke, it's a Ford. You own a Mopar.

I like Sandy's suggestion to check the distributor condenser if you're not yet running electronic. But barring that, I think it's your carb.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:39 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Dan, I forgot to mention that the choke has been wide open throughout this evening's adventures, I have never allowed the engine to cool. These symptoms started last night, there was no lead-in to this problem and my fuel filter hasnt let anything into the carb, the bowl was clean. Still not ruling out the metering block completely. I have not looked at the power valve, if that is not one and the same with the accelerator pump, that is.

Youll please excuse my ignorant tone, mental exhaustion here and there's no booze in the house.

I also just ran out and checked my points, they show no signs of burning/metal transfer.

Pony... it was a Hyundai Pony. Great little car it was except for the weak head design and poor rust resistance, but they never washed it once, I have to be fair.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 8:53 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
Still not ruling out the metering block completely. I have not looked at the power valve, if that is not one and the same with the accelerator pump, that is.
Not the same. Different.
Quote:
Pony... it was a Hyundai Pony
Those shatzboxes are much worse than Fords.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 9:22 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Quote:
Run it without the gas cap.

The tank might not be venting.
Pulled the gas cap, no "shoop" sound, tank is filled to the top with Pioneer 89 octane. It's a good thought though, Ill try driving with the cap off tomorrow.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 9:32 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
It's not gonna be your gas tank failing to vent; leave the cap on. And while this isn't a direct cause of your problem, try shopping for gas at someplace other than Pioneer. They, like Ultramar, water down their gasoline with alcohol.

Currently Esso produces the best gasoline in Ontario.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 9:49 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Really? I thought their gasoline had the highest sulfur content of all the major brands. What do you think of Sunoco?

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Thu Nov 10, 2005 11:36 pm 
Offline
Supercharged

Joined: Thu May 12, 2005 11:50 pm
Posts: 6291
Location: So California
Car Model: 64 Plymouth Valiant
Quote:
It's not gonna be your gas tank failing to vent; leave the cap on.

Maybe, maybe not.............


But since it's such an easy check might as well to cross it off the list.


Plus, you'd feel really really stupid if it is the problem and you decide not to check it..............

_________________
Ed
64 Valiant 225 / 904 / 42:1 manual steering / 9" drum brakes

8)


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 4:08 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
With all you have gone thru, here is a sugestion, that will take a little work. Get a metal can, boat gas tank, or something similar, and a cheap electric fuel pump. Hook the electric fuel pump to the container, and run a line to the carb. Put some fuel in the container, and have a friend hold the container in front seat, while you drive. Now see what happens. It you still have a problem, it is not the gas tank/sock/pickup, fuel lines, or pump. It could still be the carb, But if you have changed carbs and still have the exact same problem, that is not likely.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 4:16 am 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Well now that Ive adjusted the valves and no longer have a backfire, I am starting to think that it's ignition related. When I did a fuel pump test and saw that the output pressure did not fluctuate as the car was stumbling, I cant imagine that the flow output under these conditions would be the problem, it could not possibly maintain 4 lbs of pressure if the float has dropped and there is no fuel left in the line. I checked the needle valve, it is in good shape and isnt stuck.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 7:27 am 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
Really? I thought their gasoline had the highest sulfur content of all the major brands.
Used to. As of December '03, though, all their refineries produce very-low-sulfur motor fuels, the lowest in the market, as a matter of fact.
Quote:
What do you think of Sunoco?
I don't buy it, it's watered down with alcohol—no matter how much PR spin they apply to that practice, I avoid gasohol whenever and wherever I can. I don't like getting less (energy, mileage) for my money.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 69 posts ]  Go to page Previous 1 2 3 4 5 Next

All times are UTC-08:00


Who is online

Users browsing this forum: Bing [Bot], Google [Bot] and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited