Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 10:34 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 3 posts ] 
Author Message
 Post subject: 160Hi-Po
PostPosted: Sun Nov 13, 2005 6:31 pm 
Offline
1 BBL (New)

Joined: Sun Nov 13, 2005 5:26 pm
Posts: 2
Location: Coromandel New Zealand
Car Model:
160HP hi-po 'Australian export' version 225cid used between '68 and '69 in the australian Valiant VE and VF models (these were Dart-bodied sedans, hardtops and wagons but with some frontal treatment changes) .. Does anybody have any experience with the peculiarities of these engines which 'rock' at idle (but only when hot)..?? Is this caused by the tappet clearances tightening-up and a feature of the higher-lift increased-overlap cam used in these engines..? They also ran 9.2 compression and had the same dual-throat Carter as the 318 on a modified inlet manifold. I've got one of these and although it outperforms a stock 318 A-body ..I can't get a decent smooth idle on this engine despite going to iridium plugs and fitting all new ignition parts. Thanks.. 8)


Top
   
 Post subject: Re: 160Hi-Po
PostPosted: Sun Nov 13, 2005 6:48 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 25087
Location: North America
Car Model:
Quote:
160HP hi-po 'Australian export' version 225cid used between '68 and '69 in the australian Valiant VE and VF
Not really an export version, it was an Australian domestic item.
Quote:
'rock' at idle (but only when hot)..??
Carburettor problems, too-tight valve lash, vacuum leaks, flat camshaft lobes, faulty distributor centrifugal advance causing fluctuating timing at idle, low compression in one or more cylinders...all the normal potential causes of rough idle.
Quote:
Is this caused by the tappet clearances tightening-up
Well...overly-tight tappet clearance, yes, but no, it cannot "tighten up" at idle especially.
Quote:
and a feature of the higher-lift increased-overlap cam used in these engines..?
No, that camshaft is nothing more or less than the 244° / 244° /26° cam used on all production slant-6s in North America starting in '71. That cam does not idle rough.
Quote:
They also ran 9.2 compression
Only in the VF Pacer, which was unrated (guesstimated at 175 BHP). The regular VE-VF 2bbl 225 had standard nominal 8.5 compression.
Quote:
and had the same dual-throat Carter as the 318
No, a different Carter. Smaller venturies, smaller bores, an integral heat-tube style choke, and different jetting.
Quote:
on a modified inlet manifold.
Actually an unmodified 2bbl inlet manifold.
Quote:
can't get a decent smooth idle on this engine
Time for some systematic diagnosis!

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Mon Nov 14, 2005 7:16 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 17689
Location: Blacksburg, VA
Car Model:
I would set the valves 0.002" looser than they are now and see how that works.

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 3 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Bing [Bot], DuckDuckGo [Bot] and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited