Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Wed Nov 27, 2024 7:42 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 12 posts ] 
Author Message
 Post subject: Which O2 sensor?
PostPosted: Thu May 19, 2005 2:38 pm 
Offline
Board Sponsor
User avatar

Joined: Fri Nov 01, 2002 5:29 pm
Posts: 963
Location: Eustis, FL
Car Model: '68 V100, '68 V200, '79 Aspen, '84 D100
I picked up a budget priced A/F gauge today and ordered a 14mm O2 weld bung to install in my '84 D100.
The 3 wire is the way to go, correct?
What is a dependable brand and what auto application do I ask for to get what I need?
Does the bung weld in at a 90*, pointed towards exh flow or pointed away from exh flow?
Any tips? Am I overlooking anything?

_________________
Slant Cecil


Top
   
 Post subject:
PostPosted: Thu May 19, 2005 3:03 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Jan 14, 2003 2:37 pm
Posts: 605
Location: Fairbanks, AK
Car Model:
I used Bosch one-wire O2 sensors with "generic" wire ends (IE no brand specific connector on the end of the wire, just a generic insulated female spade terminal)

I went the one-wire route for one simple reason: less wiring to go wrong. My O2's don't take long to heat up. (Maybe 30-45 seconds)

My O2 bungs are welded perpendicular to the pipe, just past the header collector on the exhaust pipe itself. O2 sensors straight in (90* to direction of flow).

The only tip I really have to offer is to purchase a few feet of 1/4" silicon tubing, slice it lengthwise, and use it to protect the first foot or so of wiring exposed to the heat of the exhaust system.

-S/6


Top
   
 Post subject:
PostPosted: Thu May 19, 2005 6:18 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 16792
Location: Blacksburg, VA
Car Model:
Ram has it right. I wouldn't bother with a heated (3 or 4 wire) for the extra cost. Weld the bung so it's perpendicular to flow. You'll like it for tuning. I was skeptical at first, but it does save some tuning time, even with a carb.

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
 Post subject:
PostPosted: Thu May 19, 2005 7:06 pm 
Offline
Board Sponsor & Contributor

Joined: Thu Oct 31, 2002 5:39 pm
Posts: 24446
Location: North America
Car Model:
The only reason to consider a heated O2S is if your sensor port is far enough downstream that the sensor cools down at idle/low speeds and stops giving accurate readings.

_________________
一期一会
Too many people who were born on third base actually believe they've hit a triple.

Image


Top
   
 Post subject:
PostPosted: Fri May 20, 2005 11:58 am 
Offline
Board Sponsor
User avatar

Joined: Fri Nov 01, 2002 5:29 pm
Posts: 963
Location: Eustis, FL
Car Model: '68 V100, '68 V200, '79 Aspen, '84 D100
Ok, thanks guys. One wire it is. I still have the stock exh manifold, an installation a few inches from the flange should still be a hot spot.

_________________
Slant Cecil


Top
   
 Post subject:
PostPosted: Fri May 20, 2005 12:06 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 16792
Location: Blacksburg, VA
Car Model:
That should still be a very hot spot.

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
 Post subject:
PostPosted: Fri May 20, 2005 3:41 pm 
Offline
Board Sponsor & SL6 Racer
User avatar

Joined: Fri Nov 08, 2002 4:48 pm
Posts: 5835
Location: Burton BC canada
Car Model:
I have single wire O2 sensors in a couple of applications including past the collector of Loooong tube headers. In order to not screw up the ceramic coating I have it in the reducer on the drivers bank. It warms up in less than a block even in the winter. I found it lasted longer there. When the sensor was too close to the head we routinely melted it while towing up long mountain grades. ( I keep a spare in the glove box.)

_________________
Yeah....Im the one who destroyed this rare, vintage automobile.....

Image


Top
   
 Post subject:
PostPosted: Fri May 20, 2005 9:31 pm 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
Just as an fyi for those who care - generic sensors tend to be more expensive then application specific. Don't ask me why....

ie, went to napa few days ago. 4 wire o2 bosch sensor generic = $95, 1995 corvette 4 wire sensor (same thing w/gm connector at end) = $50, so something you folks may want to watch out for if your looking for heated sensors.


Top
   
 Post subject:
PostPosted: Sat May 21, 2005 2:45 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Wed Oct 23, 2002 7:06 pm
Posts: 726
Location: Asheville, NC
Car Model:
i have used the one-wire bosch o2 sensors and work fine. i think i paid 10 bucks each for them. i have also run one wire sensors from early feedback-carb honda civics (@83-85) and worked great too, plus those were free!

-james

_________________
Image


Top
   
 Post subject:
PostPosted: Sat May 21, 2005 10:41 am 
Offline
3 Deuce Weber

Joined: Wed Mar 23, 2005 7:21 pm
Posts: 86
Location: Maryland
Car Model:
My Dart has a Bosch four wire O2 sensor from Napa for a Chrysler Lebaron. It cost $60. That extra $35 is known as the "Corvette" tax. I have a '95 Corvette in addition to my Darts, and the Corvette tax runs through everything sold for that car. I used the four wire because I had a '95 Lebaron and knew the number for the part. I probably would still chose to go the four wire route just out of obsessive compulsive paranoia.

_________________
69 Dart Swinger, 230 ci slant, t-5 five speed, intercooled turbo, 4 wheel disk brakes, tubular upper control arms.


Top
   
 Post subject:
PostPosted: Sat May 21, 2005 2:28 pm 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
Dart, the 4 wire corvette sensor was $50. The generic 4 wire (no connecter, just plain uncrimped wire ends) was $95. Buy the cheaper corvette or in your case lebaron sensor, chop off the connecter, and voila you have a generic sensor thats cheaper.

I have to use a heated sensor not out of paranoia but necessesity because my sensor is about even with the transmission housing, and running clifford shorty headers.


Top
   
 Post subject:
PostPosted: Sat May 21, 2005 5:52 pm 
Offline
2 BBL ''SuperSix''

Joined: Fri May 13, 2005 8:00 pm
Posts: 13
Location: Hope, Rhode Island
Car Model:
What is the 02 sensor for? Could this be why my 85, D100 Dodge pickup runs like crap when she warms up?
/six, single barrel, automatic.
John Gov.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 12 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Ahrefs [Bot], Google [Bot] and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited