| Slant Six Forum https://slantsix.org/forum/ |
|
| Slant 6 To Borg Wagner T-5 https://slantsix.org/forum/viewtopic.php?t=32541 |
Page 1 of 1 |
| Author: | BOOKS4CARS [ Mon Dec 01, 2008 10:03 am ] |
| Post subject: | Slant 6 To Borg Wagner T-5 |
ANYONE OUT THERE HAVE A SOURCE FOR A SLANT 6 TO BORG WARNER T-5 TRANSMISSION ADAPTOR . OR ANY INFO REGARDING SAME ---I HAVE SEVERAL TRANSMISSIONS FROM S-10 CHEVYS AND THINK THEY WOULD BE A GOOD MATCH FOR MY STREET ROD PROJECT ----PLEASE CRITIQUE IF YOU THINK I AM GOING IN THE WRONG DIRECTION ---THANKS |
|
| Author: | ceej [ Mon Dec 01, 2008 11:36 am ] |
| Post subject: | |
Hi Greg, Check your PM's! CJ |
|
| Author: | Dart270 [ Mon Dec 01, 2008 12:52 pm ] |
| Post subject: | |
I did a group machining buy 3 yrs ago to put an adapter plate on a slant 6 OD bellhousing. 17 BH's were modified with the plate to mount a T5. I would post on "Parts Wanted" that you are looking for one. $300 would be a decent price for the complete bell. $350 was probably invested on each one. I have a T5 in my '64 Dart and about 5-7 other guys have done this so far. Lou |
|
| Author: | DusterIdiot [ Mon Dec 01, 2008 7:28 pm ] |
| Post subject: | Good call... |
Quote: PLEASE CRITIQUE IF YOU THINK I AM GOING IN THE WRONG DIRECTION
No that's a good call, I have a truck bell I need to figure out whether I am going A-833OD or T-5 on... after comparing all the T-5 data it looks like the mustang 5.0 has a good gear spread with OD to run 3.91/4.11 gearing without going to too granny on the 1st gear....-D.idiot |
|
| Author: | BOOKS4CARS [ Tue Dec 02, 2008 5:12 am ] |
| Post subject: | t-5 |
the only reason i am thinking t-5 is i have 2 ----one from a mid 80's v6 s-10 and one from a 4 cyl ---the v6 only had 1500 miles on it taken from a wreck ---dont know the ratios yet but i can research them on a web site called www.inliners.org ---you need the id tag from the trans and it gives all the ratios ---------the t-5 has the same bolt pattern as any chevy 3 or 4 speed so there should be a adaptor out there someware for a chevy 3 or 4 speed ---the onlt issue i see is clutch because the t-5 has a different spline count ---probably need to have a clutch custom made . clutch linkage will not be a problem because i will use a hyd slave cyl setup or possibly a hyd throw out bearing if enough room in bellhousing -----the trans should be stout enough for the slant 6 torque output --- i dont expect to pound on it regurarly ---just have to watch the hole shots and power shifting ----the s-10 trans also has a more desireable shifter location for my application as it is directly behind the gear box as opposed to the more common rear tailshaft location . ----good luck on your project and thanks -------greg |
|
| Author: | 64'4$peed [ Thu Dec 11, 2008 11:22 am ] |
| Post subject: | |
the shifter pad location on the s10 5 speeds is gonna be too far forward if this is going in an A body mopar. S10 tranny's do work good in street/hot rods though. the input shaft on the mustang tranny is also longer making it easier to reach the pilot bearing. |
|
| Author: | zedpapa [ Mon Jan 12, 2009 7:47 pm ] |
| Post subject: | |
check the trans mounting pad. i know the camaros and firebirds were machined at a 15* angle to help with shifter angle. i don't know if they did it with the trucks as well. zedpapa |
|
| Page 1 of 1 | All times are UTC-08:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|