Slant *       6       Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Mon Dec 02, 2024 5:38 am

Unanswered topics | Active topics


» » Tech Q & A » Engine

All times are UTC-08:00



Post new topic  Reply to topic  Page 1 of 1
  [ 3 posts ] 
  Print view Previous topic | Next topic 
Author Message
Family Scamp
 Post subject: Rebuilding a 225
PostPosted: Mon Sep 25, 2006 6:54 pm 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Mon Sep 25, 2006 6:07 pm
Posts: 44
Location: Boston, MA
Car Model: 1973 Plymouth Scamp
My first post to this site so suggestions on how to find info etc are welocme.

I have two questions:

In the Haynes manual it says to replace the drive plate bolts that connect it to the crankshaft if they are removed. Why? I would gladly replace but finding a 7/16 fine 1/2 inch grade 8 bolt is not easy.

I will finish rebuilding my 225 several months before the body is done and I attemp to start the engine. Other than using engine grease when I rebuild are there any other concerns or issues I should consider?

Thanks

Bruce McNulty
Top
   
Reply with quote  
Charrlie_S
 Post subject: Re: Rebuilding a 225
PostPosted: Mon Sep 25, 2006 8:13 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8712
Location: Silver Springs, Fl.
Car Model:
Quote:




In the Haynes manual it says to replace the drive plate bolts that connect it to the crankshaft if they are removed. Why? I would gladly replace but finding a 7/16 fine 1/2 inch grade 8 bolt is not easy.



Thanks

Bruce McNulty
My 1st sugestion, is to trash the Haynes manual, and get the proper Factory Service Manual.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225
Top
   
Reply with quote  
Doctor Dodge
 Post subject: Re: Rebuilding a 225
PostPosted: Mon Sep 25, 2006 10:38 pm 
Offline
Guru
User avatar

Joined: Sat Oct 12, 2002 11:22 am
Posts: 3740
Location: Sonoma, Calif.
Car Model: Many Darts and a Dacuda
Quote:
My first post to this site so suggestions on how to find info etc are welcome.

I have two questions:

In the Haynes manual it says to replace the drive plate bolts that connect it to the crankshaft if they are removed. Why? I would gladly replace but finding a 7/16 fine 1/2 inch grade 8 bolt is not easy...
I re-use these bolts all the time and never had a problem. I never saw any warning to not reuse these bolts in the FSM.
Quote:
I will finish rebuilding my 225 several months before the body is done and I attemp to start the engine. Other than using engine grease when I rebuild are there any other concerns or issues I should consider?

Thanks
Bruce McNulty
Tape-off / plug any openings.
Keep the engine in a dry place and turn it over with a wrench ever month or so.
DD
Top
   
Reply with quote  
Display posts from previous:  Sort by  
Post new topic  Reply to topic  Page 1 of 1
  [ 3 posts ] 

» » Tech Q & A » Engine

All times are UTC-08:00

Who is online

Users browsing this forum: Ahrefs [Bot] and 16 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited