Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Tue Nov 26, 2024 4:26 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 190 posts ]  Go to page Previous 1 2 3 4 5 613 Next

Will the engine last more than one 1/4 mile pass?
yes 89%  89%  [ 74 ]
no 11%  11%  [ 9 ]
Total votes: 83
Author Message
 Post subject:
PostPosted: Tue May 15, 2007 6:44 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Pulled the radiator, and installed a NOS damper. Fired the motor back up, and brought the revs up in gear, with the brakes applied. Ran through the gears, and could feel the shifts in all gears. I guess it is ok, just couldn't feel the shift with a 3,000 converter and no load. Corrected a few small leaks, and did a little wireing. Lowered it from the jack stands and backed it out of the garage, under it's own power. She saw daylite for the first time in over a year. Still have a lot to do, will keep posting.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Tue May 15, 2007 7:01 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14487
Location: Park Forest, Illinoisy
Car Model: 68 Valiant
Cool deal Charlie! :D

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Wed May 16, 2007 1:12 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8916
Location: Cox’s Creek, KY
Car Model: More cars than sense...
That's great Charrlie!

_________________
Rob

I’m Mater
The Kentucky Poser

Image
Image
Image


Top
   
 Post subject:
PostPosted: Wed May 16, 2007 3:30 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Trailered the car to town, today, Got a front end alignment, and put it on the scale. 2,740 with me in it. Will probably be between 50 and 100 lbs heavier, when done. Real lightweight compared to my Cuda.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Fri May 18, 2007 7:39 am 
Offline
EFI Slant 6
User avatar

Joined: Fri Jan 05, 2007 2:57 pm
Posts: 355
Location: Florida
Car Model:
Cool Charrlie, nice to see some lite, at the end of our tunnel vision. :lol: We will also be able to drive the TWISTER from back yard to front. Just need to cut and weld drive shaft this weekend. Talk to you soon.Don

_________________
'72 Image Duster /6 with turbo build up
'03 Ram 2500 4x4 w/HEMI 5sp 4:10 posi
My Twister Page


Top
   
 Post subject:
PostPosted: Fri May 18, 2007 9:01 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Quote:
Trailered the car to town, today, Got a front end alignment, and put it on the scale. 2,740 with me in it. Will probably be between 50 and 100 lbs heavier, when done. Real lightweight compared to my Cuda.
Actually, decieded to try and get some more weight out. The weight break between "B" and "C" is at 2700 lbs, I was thinking it was 2800. I want to be right on the split, so I can run in either class.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Sat May 19, 2007 4:52 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Quote:
Quote:
Trailered the car to town, today, Got a front end alignment, and put it on the scale. 2,740 with me in it. Will probably be between 50 and 100 lbs heavier, when done. Real lightweight compared to my Cuda.
Actually, decieded to try and get some more weight out. The weight break between "B" and "C" is at 2700 lbs, I was thinking it was 2800. I want to be right on the split, so I can run in either class.
Should be below 2700 lbs. Removed the front bumper, and the stock seat. Installed a aluminum racing seat, I had up in the rafters. Neighbor, came over and put him to work, sanding the roof. Then we gave it a coat of rattle can primer.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Sun May 20, 2007 1:37 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8916
Location: Cox’s Creek, KY
Car Model: More cars than sense...
Sounds like fun Charrlie! Wish I could be there to help too. Keep us posted.

_________________
Rob

I’m Mater
The Kentucky Poser

Image
Image
Image


Top
   
 Post subject:
PostPosted: Sun May 20, 2007 6:05 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Took the car up to Gainesville Raceway, last night. Worked on it till late, and did not have it quite "race ready". I live on a dirt road, and this is not a street car, so wanted to just drive it, and make sure there were no major problems. Ran the car through tech, just two minor issues, they wanted corrected, but it would not have prevented me from running. Drove it around the pits, and, did one very short "holeshot". Can't do too much in the pits, tracks "frown" on that. The engine feels pretty good. Still have a trans pan gasket leak. I am going to install a new deep pan kit, and reusable gasket, today. I am tired trying to stop the seepage. Hope to finish wireing the tach and the nitrous system, today. Then 1 more day just going over the car, to check everything. Hopefully a test and tune on Wed nite. See if it can run in the 15's on motor.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Sun May 20, 2007 12:59 pm 
Offline
3 Deuce Weber
User avatar

Joined: Fri Jul 04, 2003 7:52 am
Posts: 64
Location: Gibbstown, NJ
Car Model:
Charlie, you got us on the edge of our seats, this is great... keep it up...

_________________
65 Coronet, 4 bbl, .060 over, mild cam.
66 Valiant, Black, 3spd, Hyperpak, headers.
works in progress...


Top
   
 Post subject:
PostPosted: Sun May 20, 2007 9:17 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Quote:
Charlie, you got us on the edge of our seats, this is great... keep it up...
Good to know this is of interest to someone. Finally makeing good progress, after 2 years of procrasinating.

Installed the Mopar Performance deep trans pan and pickup. Used the "new" style gasket. All the gauges, tail lights, dash/gauge lites are all hooked up and working. Had to install a new light switch, for the gauges lights (bad reostat).

Ordered a new seat belt from Summit. I cannot use a 4 year old RCI lap belt, but a 31 year old stock belt is OK. What a stupid rule. Aftermarket belts can not be more then 2years old.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Mon May 21, 2007 12:39 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Wed Jan 29, 2003 4:42 am
Posts: 8916
Location: Cox’s Creek, KY
Car Model: More cars than sense...
Quote:
Quote:
Charlie, you got us on the edge of our seats, this is great... keep it up...
Good to know this is of interest to someone. Finally makeing good progress, after 2 years of procrasinating.

Installed the Mopar Performance deep trans pan and pickup. Used the "new" style gasket. All the gauges, tail lights, dash/gauge lites are all hooked up and working. Had to install a new light switch, for the gauges lights (bad reostat).

Ordered a new seat belt from Summit. I cannot use a 4 year old RCI lap belt, but a 31 year old stock belt is OK. What a stupid rule. Aftermarket belts can not be more then 2years old.
I enjoy following along on your progress too Charrlie. I totally agree with the seat belt rule. I have brand new (used once last year) RCI 5 point harnesses in the Duster that won't be good next year. After the race last year I removed them and put them back in the original box to preserve them. Another waste of money I guess... :roll:

Keep us posted.

_________________
Rob

I’m Mater
The Kentucky Poser

Image
Image
Image


Top
   
 Post subject:
PostPosted: Mon May 21, 2007 5:42 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14487
Location: Park Forest, Illinoisy
Car Model: 68 Valiant
Quote:
Good to know this is of interest to someone. Finally makeing good progress, after 2 years of procrasinating.
I'm watching too Charlie. :wink:
Quote:
Ordered a new seat belt from Summit. I cannot use a 4 year old RCI lap belt, but a 31 year old stock belt is OK. What a stupid rule. Aftermarket belts can not be more then 2years old.
Welcome to the land of lawyers Charlie. Look at the bright side, you can sell the old ones to a dirt track racer. They don't have to have theirs date coded. (at least around here)

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Mon May 21, 2007 6:33 am 
Offline
Board Sponsor & SL6 Racer
User avatar

Joined: Fri Nov 08, 2002 4:48 pm
Posts: 5835
Location: Burton BC canada
Car Model:
Im listening Mr S. .............

_________________
Yeah....Im the one who destroyed this rare, vintage automobile.....

Image


Top
   
 Post subject:
PostPosted: Mon May 21, 2007 8:34 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 8701
Location: Silver Springs, Fl.
Car Model:
Couldn't believe it. Went out to the shop, and had a puddle of trans fluid under the car :? . It was seeping from the drain plug. Damm nylon plug gasket. Had to tighten it so tight, I was worried about stripping it, but that cured the problem. Mounted the nitrous tank and finished the wireing. While I was under the car, on the trans leak, I noticed the driveshaft had a scrape on it from the driveshaft loop. So had to do a little relocating. Float on the secondary, stuck and had to fix that. Car is now loaded on the trailer for another trip to the alignment shop. It has a pull to the right, I am not happy with. Once that is fixed, I have a couple of holes in the floor and firewall, to be plugged, than a final look over, and off to the track, on Wed night. Also had to replace the "acorn" lugnuts on the rear wheels, for open stock style nuts, so the tech guys can verify the studs are long enough. I am running 13 inch "wagon wheels", 8 inch wide, with 22x9x13 slicks.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 190 posts ]  Go to page Previous 1 2 3 4 5 613 Next

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited