Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 12:43 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 7 posts ] 
Author Message
 Post subject: Spec Clutch Problem
PostPosted: Sun May 16, 2010 7:36 am 
Offline
TBI Slant 6

Joined: Sat Mar 06, 2010 6:21 pm
Posts: 122
Location: Lockport New York
Car Model:
Just installed diaphram style 9 in kevlar unit. I have not called Matt yet but this unit slips bad trying to accealerate in 2nd gear. If I feather trottle I can get in to 3rd but give it any power and the motor just breaks away. I do not think this is the answer to our clutch problem kevlar disk dosn't seem to have enought friction material and diaphram cover not enought pressure. Has anybody else got one in car and working. Yes I have 1/4 in clearance between throw out and fingers on plate and flywheel was machined and cleaned along with cleaned pressure plate surface. I am going to call Matt monday will try to post after that


Top
   
 Post subject:
PostPosted: Sun May 16, 2010 9:33 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14982
Location: Park Forest, Illinoisy
Car Model: 78 Volare
Just asking, but why would you expect a 9" clutch to hold a blown motor no matter what it's made of? :?

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Sun May 16, 2010 10:16 am 
Offline
Board Sponsor & SL6 Racer
User avatar

Joined: Fri Nov 08, 2002 4:48 pm
Posts: 5835
Location: Burton BC canada
Car Model:
I have a 9.25" kevlar unit (last of the McLeod)

I use a stock 9.25 diaphram and flywheel.

My car makes mebbe 175hp and has 3.55 gears. Car weight 3000lbs

I usually let the clutch out at an idle ,,,,,then nail it.

I can do burnouts with it as long as Im assured wheelspin (235/60/14)

Its fine for anything other than a hooked up launch......

If you smoked it even once you will need to start over.

_________________
Yeah....Im the one who destroyed this rare, vintage automobile.....

Image


Top
   
 Post subject:
PostPosted: Sun May 16, 2010 10:48 am 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
If you read about Spec Clutch around the 'net you'll find that many people have slipping problems. I think that Spec overrates the torque capacity of their clutches. Still I ordered a 9" clutch from Spec Monday the 10th, but having read other people's experiences I went with a 6-puck metallic disc. My engine also is normally aspirated and just 174ci (it's +.040" overbore 170) so it will make a lot less torque than a blown 225.

I had a full Kevlar faced 9 1/4" clutch disc with a Borg and Beck cover before. Even with 9 springs in the cover (instead of the 6 stock springs) it was marginal behind a mild 318 (222hp and 249 ft/lbs at the rear wheels). This is another reason I did not choose Kevlar for my new clutch.

_________________
Joshua


Top
   
 Post subject: Re: Spec Clutch Problem
PostPosted: Sun May 16, 2010 5:27 pm 
Offline
TBI Slant 6

Joined: Sat Mar 06, 2010 6:21 pm
Posts: 122
Location: Lockport New York
Car Model:
Quote:
Just installed diaphram style 9 in kevlar unit. I have not called Matt yet but this unit slips bad trying to accealerate in 2nd gear. If I feather trottle I can get in to 3rd but give it any power and the motor just breaks away. I do not think this is the answer to our clutch problem kevlar disk dosn't seem to have enought friction material and diaphram cover not enought pressure. Has anybody else got one in car and working. Yes I have 1/4 in clearance between throw out and fingers on plate and flywheel was machined and cleaned along with cleaned pressure plate surface. I am going to call Matt monday will try to post after that
I think spec rates this clutch package at 550 ft lb with it breaking away at 1/3 throttle I should quit my day job and bulid supercharged engines cause I must be makeing over 1500 ft lb. Seriously ether I have a defective piece or its junk.


Top
   
 Post subject:
PostPosted: Sun May 16, 2010 6:15 pm 
Offline
Site Admin
User avatar

Joined: Mon Mar 31, 2003 1:04 pm
Posts: 7471
Location: Oregon
Car Model: 2023 Eichman Digger?
I did a center-force clutch on an over-baked big block to solve problems like your having. At WOT it would break loose fully engaged as the engine spun up. The center-force didn't break loose. Ran it for many years.

2¢

CJ

_________________
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Tue May 18, 2010 2:23 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
Have you contacted Spec about your clutch problems yet? I just got my clutch from them today. It's really 8 7/8" or 225mm. As I wrote before I bought the 6-puck metallic disc.

_________________
Joshua


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 7 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited