Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 7:37 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Thu May 27, 2010 6:12 pm 
Offline
3 Deuce Weber

Joined: Mon Oct 25, 2004 6:06 pm
Posts: 97
Location: Kansas City Kansas
Car Model:
Bought a 1980 pickup for the slant 6 and 4sp. overdrive. Less than a week later I had a chance to buy a short tail shaft 833 od supposedly
from a 1977 f body. The output shafts are of different diameters.
1 1/4" versus 1 1/16" for the short tail shaft. Will a 1966 valiant yoke and driveshaft fit the smaller output shaft.


Top
   
 Post subject:
PostPosted: Thu May 27, 2010 7:12 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
Yes, the smaller slip yoke from the '66 Valiant should fit the small output shaft A833OD just fine. I don't know if the driveshaft will fit because you didn't say what the vehicle is or if anything other than the transmission (like the rear end) is being changed.

_________________
Joshua


Top
   
 Post subject:
PostPosted: Thu May 27, 2010 9:12 pm 
Offline
3 Deuce Weber

Joined: Mon Oct 25, 2004 6:06 pm
Posts: 97
Location: Kansas City Kansas
Car Model:
Joshua, thanks for the quick reply. I forgot to mention that the Valiant will have a 8 inch ford rear end out of a Maverick. I would like to use the Valiant drive shaft and have the rear U joint changed to the ford type.The car now has a 230 3 speed with the overdrive type bellhousing.


Top
   
 Post subject:
PostPosted: Thu May 27, 2010 9:48 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
So the car is a '66 Valiant? The Maverick rear end should be fine as long as the driveshaft doesn't bottom out in the trans. When you have the Ford U-joint put on the back of the driveshaft you might have it shortened 1/2".

_________________
Joshua


Top
   
 Post subject: Yep...
PostPosted: Fri May 28, 2010 6:28 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
Just as an FYI for on lookers...to clarify Josh's train of thought.

The 1975-1976 A-Body A-833OD's seem to have the 29/30 spline output shaft for the A-727 yoke, as well as all the Truck long tailshaft boxes... Somewhere about 1977-1978 Mopar decided that the A-904 25/26 spline yoke should be the key for the (A)/F-body A-833OD trannies. So keep this in mind when buying a "yard" tranny, that you may need a different yoke to make the conversion work depending on your current tranny.

Note: I did see one guy at a yard try to sell one to a guy by jambing the 30 spline yoke into the back of the 26 spline tailshaft and tell him it fits fine...after they couldn't get the yoke out, i picked the tranny and yoke up for cheap...take the time to count the splines, before thinking the yoke just needs a bit more of a push.... :wink:


-D.Idiot


Last edited by DusterIdiot on Fri May 28, 2010 8:20 pm, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Fri May 28, 2010 7:01 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
DI is right.

Also, I have a couple of '66-'67 A-body A833 4-speeds. These have 26 spline main shafts too.

_________________
Joshua


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 6 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited