Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 12:43 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Tue Jun 25, 2013 5:56 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13431
Location: Fircrest, WA
Car Model: 76 D100
I am gathering materials and instructions on how to upgrade the 2.2 rear gears in the 8.25 rear axle in my brother's Duster to 3.2 rear gears out of a mid-70s Dodge van rear axle. I have the full carrier to go with the 3.2 gears due to the size difference in the 2.2 gear carrier and the lower ratio carriers.

Anyway, my question is about the special tool for the adjusters in the rear axle. I have read that a 1 1/4 inch nut welded onto some all-thread will work, but I have also heard that old A-body torsion bars also work. Is that true?

Thanks!


Top
   
 Post subject:
PostPosted: Tue Jun 25, 2013 6:10 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
"A" body bars are too small for the adjuster on a 7 1/4 rear. I think it is either "B" or "C" body bars.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Tue Jun 25, 2013 6:20 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13431
Location: Fircrest, WA
Car Model: 76 D100
Did you mean 7 1/4 or 8 1/4 rear axle? I will guess you meant 8 1/4 since I will assume the adjusters on the 8 1/4 are bigger than the 7 1/4 and if the A-body torsion bars worked on any axle it would be the smallest (the 7 1/4). Looks like it is time to break down and buy the tool or make one out of a nut and some all-thread.


Top
   
 Post subject:
PostPosted: Tue Jun 25, 2013 8:47 pm 
Offline
Turbo Slant 6
User avatar

Joined: Fri Apr 27, 2007 5:50 pm
Posts: 745
Car Model:
you are looking for a c body tortion bar to use for the adjuster not an abody

_________________
1966 Plymouth Valiant, 225, 3 on the tree, 8 1/4 3.21 sure grip, hyperpac, holley 650dp, holset h1c
Image


Top
   
 Post subject:
PostPosted: Tue Jun 25, 2013 9:42 pm 
Offline
Supercharged
User avatar

Joined: Sun Nov 03, 2002 9:20 pm
Posts: 13431
Location: Fircrest, WA
Car Model: 76 D100
Got it. Looks like I will be tracking down the correct tool. Thanks for the input guys.


Top
   
 Post subject:
PostPosted: Wed Jun 26, 2013 5:00 am 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
Quote:
Did you mean 7 1/4 or 8 1/4 rear axle? I will guess you meant 8 1/4 since I will assume the adjusters on the 8 1/4 are bigger than the 7 1/4 and if the A-body torsion bars worked on any axle it would be the smallest (the 7 1/4). Looks like it is time to break down and buy the tool or make one out of a nut and some all-thread.
I meant the 7 1/4. I have never done a 8 1/4, and was assuming if the "A" body bars were too small for the 7 1/4, they would be too small for the 8 1/4 also. Actually what I did was use a broken "A" body bar, and weld a nut to that. I would have to measure the size of the nut, as at my age I have CRS.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject:
PostPosted: Wed Jun 26, 2013 10:59 am 
Offline
Turbo Slant 6

Joined: Tue Mar 16, 2004 6:25 am
Posts: 831
Location: Tompkinsville, KY
Car Model:
I think both axles use the same size adjuster/tool.
I made a tool using a common 36mm (about 1 7/16") hex axle nut (Honda, etc.) that you should be able to find used laying around any mechanic shop.
I had a piece of aluminum curtain/shower rod that fit nicely inside it, so I used the stake flange of the nut to lock them together.
Works beautifully.

_________________
O==\=/==O

"A mechanic is Somebody."
- Jim Preston


Top
   
 Post subject:
PostPosted: Mon Jul 08, 2013 5:32 pm 
Offline
Supercharged
User avatar

Joined: Sat Nov 27, 2004 8:03 pm
Posts: 10444
Location: IRWIN PA
Car Model:
YOu can also use an F-J-M curved bar for this job.

Cut the Hex off of it and weld it to a straight shaft.

it is the correct size as I have done this.



Greg

_________________
http://www.youtube.com/hyperpack

Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 8 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited