Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 6:06 am

All times are UTC-08:00




Post new topic  Reply to topic  [ 12 posts ] 
Author Message
 Post subject: D150 4 speed shifter
PostPosted: Wed Apr 23, 2014 11:34 am 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Sat Apr 12, 2014 5:53 pm
Posts: 40
Location: Leesville SC
Car Model:
Hey Guys,
I just noticed some differences in shifter locations for the D150. I have an 84 D150 custom. Slant of course and the 4 speed. I was looking around at some pics on the net and I saw an 84 prospector with a 4 speed and the shifter in that truck had a curved long handle and was connected right to the trans tunnel forward up near the dash. Whereas mine has a shorter handle and it sits on a sheet metal pedestal that is attached to the left side of my trans tunnel just in front of the bench seat. Can someone shed some light on this for me. I'm getting ready to order a new vinyl floor for the truck and the location of the shifter cutout may be an issue.


Top
   
 Post subject:
PostPosted: Wed Apr 23, 2014 5:00 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3868
Location: Indianapolis
Car Model:
a833 was not the only manual tranny offered,
there was a second manual, completely different from the a833, the name escapes me at this moment,, that had a genuine granny gear, I believe it was a top loader..


Top
   
 Post subject:
PostPosted: Wed Apr 23, 2014 6:47 pm 
Offline
Supercharged
User avatar

Joined: Thu Jan 27, 2005 8:32 pm
Posts: 7834
Location: Portland-ish
Car Model: Fiat 500e
The overdrive transmission is the A833OD and has an external shifter on the left side. The heavy duty 4 speed is the NP435 family and has the shifter in the top cover.

_________________
Joshua


Last edited by Joshie225 on Thu Apr 24, 2014 4:00 pm, edited 1 time in total.

Top
   
 Post subject: Np435
PostPosted: Wed Apr 23, 2014 6:50 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
D-150's only got the Np435 and the HD springs since they were the 'load haulers'

The only way to get a shifter for it is to buy another good tranny at a junkyard. Sadly these are boat anchors and typically get tossed with the slantsix as scrap, luckily they used that tranny from the 60s to the late-80's, so there should be one if your local yard has a row of 80's Dodge trucks.


Top
   
 Post subject:
PostPosted: Thu Apr 24, 2014 3:41 pm 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Sat Apr 12, 2014 5:53 pm
Posts: 40
Location: Leesville SC
Car Model:
Quote:
-150's only got the Np435 and the HD springs since they were the 'load haulers'
?? :? Ok now I'm confused. My truck is a D150 but it has a A833OD, says so on the label on the hood. So maybe my truck isn't a D150? Well its got D150 badges on it.
My delema is if I order a vinyl floor for an '84 D150 is the cutout for the shifter going to be in the correct location. Or since I have the A833 with the shifter located on the side of the tunnel. Should I order a mat for the W100, or W150.


Top
   
 Post subject:
PostPosted: Thu Apr 24, 2014 6:01 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3868
Location: Indianapolis
Car Model:
the W's are the 4 wheel drive versions
the od a833 is the standard manual tranny for the 80's D-150's, NP435's were also offered.
here is some NP435 info

https://www.novak-adapt.com/knowledge/np435.htm

, when I purchased replacement carpet for my 83 D-150,, I had to cut out the hole for the floor shifter..you can check with the carpet supplier to see how they provide it.

by the way, I am not sure what
Quote:
D-150's only got the Np435 and the HD springs since they were the 'load haulers'
means myself,, and I have an 83 D-150,,a833...


Top
   
 Post subject: Sure...
PostPosted: Thu Apr 24, 2014 7:47 pm 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
Quote:
the od a833 is the standard manual tranny for the 80's D-150's, NP435's were also offered.
I could see that, although I've never seen one optioned like it, and the junkyards are littered with NP435 or 727 80's D-150's...Typically the A-833OD is seen in the D-100's, it just seems a bit odd they would consider that combination since the A-833OD would not last long with a yard an a half of gravel in the bed (but a 1-barrel 225 and the NP-435 has no problem hauling that load, been there, rode in that).

When in doubt, you can look under the truck at the tranny tunnel and see where the shift hump is located and if there has been any mods done. If the build sticker matches the VIN, then it's a factory job.


Top
   
 Post subject:
PostPosted: Thu Apr 24, 2014 8:06 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3868
Location: Indianapolis
Car Model:
Quote:
the junkyards are littered with NP435
maybe it is a location thing,, around here,, in the pull aparts,, I have seen exactly one NP435, it was in a D-250, had a heavy duty frame hitch and a rear sway bar,, I got both of those for my D-150..

all the manual tranny D series trucks I have seen are a833's
the a833 is not exactly a slouch..


Top
   
 Post subject:
PostPosted: Tue Apr 29, 2014 6:00 am 
Offline
4 BBL ''Hyper-Pak''
User avatar

Joined: Fri Feb 24, 2012 6:58 pm
Posts: 48
Location: NB Canada
Car Model:
I have also seen a few with the 833 (like mine) it can haul just not as much. (I have done 6 200-250lb chucks on concrete once. tranny didn't mind. 32 year old springs did.) Actually I don't think I have seen the other tranny except in manuals. If anything I agree with contacting the company. If it does not specify the tranny it might be a cut yourself deal. I wouldn't assume. I have seen far too many parts places not know anything about the slant 6 and the vehicles that carried them.

(typed while holding a baby. Next gen slant 6er)

_________________
Image


Top
   
 Post subject:
PostPosted: Sat May 03, 2014 11:12 am 
Offline
EFI Slant 6
User avatar

Joined: Thu Apr 05, 2007 9:49 am
Posts: 289
Location: Leesburg Indiana
Car Model:
My 86 has the 833od also.
And according to Brewers Performance it is a Hurst shifter they used with the 833.
So the rebuild kit for the shift is the same for all Husrt shifters that they sell.

Dave

_________________
86 Miser 170,000+
2 1/4" exhaust
Holley 1920 #55
HEI MSD BLaster 2
17.8 mpg


Top
   
 Post subject: Correct...
PostPosted: Sat May 03, 2014 11:17 am 
Offline
Board Sponsor
User avatar

Joined: Tue Oct 29, 2002 8:27 pm
Posts: 9714
Location: Salem, OR
Car Model:
Quote:
And according to Brewers Performance it is a Hurst shifter they used with the 833.
This also applies to the cars as well, except for a few years in the 60's where they could be equipped with the inland shifter.

FYI.

With some bench space and a few common tools the hurst shifter is easy to disassemble clean out, replace worn missing parts, lube, and reassemble.

-D.idiot


Top
   
 Post subject:
PostPosted: Sat May 03, 2014 6:38 pm 
Offline
Supercharged

Joined: Wed Sep 17, 2008 6:48 pm
Posts: 3868
Location: Indianapolis
Car Model:
and here is an article with info on setting up a shifter and linkage

http://www.mobiloil.com/USA-English/Mot ... .aspx?pg=1


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 12 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited