Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Fri Nov 20, 2026 7:30 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 11 posts ] 
Author Message
PostPosted: Fri May 23, 2014 12:19 pm 
Offline
Supercharged

Joined: Sun Jun 04, 2006 4:53 pm
Posts: 4295
Location: Gaithersburg MD
Car Model:
This is a question for those of you who have 8 & 3/4" rears in your cars. Is there a train plug in the case of them? This Ford rear, which has a separate pumpkin, from the late 80's has none. When I tipped the rear up on end after pulling the axles, something akin to mud came out. It certainly looked as if it had never been changed. How could it with no drain plug?

I am wondering if it is reasonable to put a drain plug in the case, and where it is on the Mopar units. I could drill a hole in the case and tap it for an NPT plug.

I do not know if other rear ends with removable pumpkins had drains in the case. Thanks for any feedback on this.

Sam

_________________
Image


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 1:28 pm 
Offline
Supercharged
User avatar

Joined: Sat Feb 16, 2008 1:25 pm
Posts: 5623
Location: Downeast Maine
Car Model:
Looking down drive shaft to pumpkin it is on the left, or in other words in the passenger's side about half way between top and bottom of casting.

_________________
67' Dart GT Convertible; the old Chrysler Corp.
82' LeBaron Convertible; the new Chrysler Corp
07' 300 C AWD; Now by Fiat, the old new Chrysler LLC

Image


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 1:52 pm 
Offline
Supercharged

Joined: Sun Jun 04, 2006 4:53 pm
Posts: 4295
Location: Gaithersburg MD
Car Model:
That sounds like the filler hole, which this has. Is there a drain as well?
Sam

_________________
Image


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 2:20 pm 
Offline
6 Pack Dart
User avatar

Joined: Sat Nov 02, 2002 5:44 pm
Posts: 2281
Location: Eugene, Oregon
Car Model:
There is no drain hole on Ford 8" you must partly remove all flange nuts and pull center section partly out to drain.

Richard

_________________
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 2:27 pm 
Offline
Supercharged
User avatar

Joined: Sat Nov 27, 2004 8:03 pm
Posts: 10444
Location: IRWIN PA
Car Model:
or get a small hand held cheapo suction / transfer pump and get suckin out the filler hole..


otherwise you will need to add / weld in some sort of drain if you want one.

Greg

_________________
http://www.youtube.com/hyperpack

Image


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 2:42 pm 
Offline
Board Sponsor
User avatar

Joined: Fri Nov 01, 2002 5:02 pm
Posts: 1868
Location: Waterloo, Iowa
Car Model: '23 T-bucket
I'v got a '59 Chevy rear that has both a fill port and drain plug in the main housing. Drain plug is bottom center, while the fill port is centered at the back, about 1/3 the way up from the bottom.

You may be able to drill/tap the bottom center of the main housing for a plug, but do make sure it won't interfere with the ring gear on the inside.

Roger


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 4:35 pm 
Offline
6 Pack Dart
User avatar

Joined: Sat Nov 02, 2002 5:44 pm
Posts: 2281
Location: Eugene, Oregon
Car Model:
I think you will find the housing is too thin to just drill and tap. You should if you want a drain plug empty the housing, clean all lube traces and weld a plate to be drilled and tap it for drain plug.

Richard

_________________
Part of Tyrde-Browne Racing


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 6:12 pm 
Offline
Supercharged

Joined: Sun Jun 04, 2006 4:53 pm
Posts: 4295
Location: Gaithersburg MD
Car Model:
Thanks all. I will likely make no changes. I probably won't live as long as this axle is old now.

Sam

_________________
Image


Top
   
 Post subject:
PostPosted: Fri May 23, 2014 11:08 pm 
Offline
Board Sponsor & Moderator
User avatar

Joined: Thu Oct 17, 2002 7:27 pm
Posts: 14984
Location: Park Forest, Illinoisy
Car Model: 78 Volare
Moser makes some very nice fill/drain plugs that come with weld-in bungs.

_________________
Official Cookie and Mater Tormentor.


Top
   
 Post subject:
PostPosted: Sat May 24, 2014 2:48 am 
Offline
Supercharged

Joined: Sun Jun 04, 2006 4:53 pm
Posts: 4295
Location: Gaithersburg MD
Car Model:
Hmmmm.

Sam

_________________
Image


Top
   
 Post subject:
PostPosted: Sat May 24, 2014 12:39 pm 
Offline
Supercharged
User avatar

Joined: Sat Feb 16, 2008 1:25 pm
Posts: 5623
Location: Downeast Maine
Car Model:
There is no drain plug, and not much room to snake in a small tube to suck oil out is a Suregrip. I purchased a "rear end sucker outer", yeah I get it, innuendo intended..., and the tube would not reach very deep into pumpkin; waist of money.

_________________
67' Dart GT Convertible; the old Chrysler Corp.
82' LeBaron Convertible; the new Chrysler Corp
07' 300 C AWD; Now by Fiat, the old new Chrysler LLC

Image


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 11 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited