Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Thu Nov 28, 2024 8:49 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 10 posts ] 
Author Message
PostPosted: Thu Apr 14, 2005 12:49 pm 
Offline
TBI Slant 6

Joined: Thu Jul 22, 2004 2:21 pm
Posts: 128
Location: Lyons, CO
Car Model:
I'm thinking its time to change out the antifreeze in my dart, But I want to get out as much of the old antifreeze as possible. Is there a drain plug on the block somewhere so I can drain out more of the old stuff ?? I kind of looked around at it but didnt see anything.
Any other ideas for doing a complete drain ?

Thanks


Top
   
 Post subject: Suggestions
PostPosted: Thu Apr 14, 2005 1:05 pm 
Offline
Board Sponsor

Joined: Tue Jul 27, 2004 9:27 am
Posts: 824
Location: Pittsburgh, PA
Car Model:
There is usually a plug that screws into the block on the passenger side near the firewall. It's often easier to see from the underside.

A good idea is to remove the heater core hoses from the engine and backflush with a garden hose.

Might help to remove the thermostat during the flush, but reassembling the hose/housing.

_________________
1980 Aspen 225 super six
Image


Top
   
 Post subject:
PostPosted: Thu Apr 14, 2005 1:10 pm 
Offline
TBI Slant 6

Joined: Thu Jul 22, 2004 2:21 pm
Posts: 128
Location: Lyons, CO
Car Model:
Thanks, i'll take a look in that location and see if I can find it.

Scott


Top
   
 Post subject:
PostPosted: Thu Apr 14, 2005 10:40 pm 
Offline
Turbo EFI
User avatar

Joined: Sun Nov 03, 2002 1:49 pm
Posts: 2445
Location: Lubbock, TX
Car Model:
The plug is just aft of the oil filter. Take it out and you may have to poke in a screwdriver to loosen the crud. Don't worry, you won't hurt anything. You may also have to stand on your wrench to get the plug to turn...I know I did! Replace the plug with a petcock to make future cleanings easier.


Top
   
 Post subject: Flush Kit
PostPosted: Fri Apr 15, 2005 7:17 am 
Offline
EFI Slant 6
User avatar

Joined: Thu Feb 24, 2005 7:04 am
Posts: 269
Location: harford co. maryland
Car Model:
Prestone actually makes a flush kit that works real well you splice a T conector in to you heater hose that your garden hose will hook up to then their is a spout that goes whare your radiator cap goes and it spits all the water out when you run the car

thanks


Top
   
 Post subject:
PostPosted: Fri Apr 15, 2005 9:13 am 
Offline
TBI Slant 6

Joined: Thu Jul 22, 2004 2:21 pm
Posts: 128
Location: Lyons, CO
Car Model:
Thanks for the info guys,, I'm going to give some of them a try this weekend.


P.S. I posted a while back about my heater not putting out much heat. I changed out the heater core a couple weeks ago. And now it makes great heat. The old core must have been a little crudded up inside.


Top
   
 Post subject: Prestone kit
PostPosted: Fri Apr 15, 2005 10:19 am 
Offline
4 BBL ''Hyper-Pak''

Joined: Sat Mar 26, 2005 3:48 pm
Posts: 41
Location: St. Louis Mo
Car Model:
The Prestone kit work real well. I'd stay away from removing that plug from the engine block. Check out that kit, Advance and O'Riely and auto zone should carry it.


Top
   
 Post subject: Re: Prestone kit
PostPosted: Fri Apr 15, 2005 6:51 pm 
Offline
Board Sponsor
User avatar

Joined: Wed Oct 23, 2002 7:54 pm
Posts: 658
Location: Hutchinson, MN
Car Model:
Quote:
The Prestone kit work real well. I'd stay away from removing that plug from the engine block. Check out that kit, Advance and O'Riely and auto zone should carry it.
I prefer to remove the plug. That is where all the crud settles in the block.

Be sure to use a snug fitting box end wrench or a 6-point socket or you'll round off the corners. This is assuming it has a hex head plug like all of mine have.


Top
   
 Post subject:
PostPosted: Fri Apr 15, 2005 6:55 pm 
Offline
Turbo EFI
User avatar

Joined: Mon Jul 14, 2003 10:02 am
Posts: 1817
Location: Southeastern Pennsylvania
Car Model:
Pull the plug. it will flush so much faster if you drain the block first.

_________________
ImageImage


Top
   
 Post subject:
PostPosted: Mon Apr 18, 2005 5:49 pm 
Offline
Turbo EFI
User avatar

Joined: Sat Nov 29, 2003 5:45 pm
Posts: 1903
Location: Hamilton the STEEL CITY, ON
Car Model:
Seconded, actually when flushing the system with a garden hose you will get sediment out of the water jackets more effectively with the plug out than by any other method. That plug is right at the bottom corner of the water jacket.

_________________
I've been calling it as i see it for my entire life and that's not about to change. Take it or leave it.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 10 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: Ahrefs [Bot], Bing [Bot], Google [Bot], Semrush [Bot] and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited