Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Wed Nov 27, 2024 9:48 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Tue May 03, 2005 11:43 pm 
Offline
2 BBL ''SuperSix''
User avatar

Joined: Mon Mar 08, 2004 9:38 pm
Posts: 22
Location: Cincinnati, Ohio
Car Model:
Hi, I have a 75 Duster, and all the lights behind the speedo are out, Before I go tearing the dash apart, I was hoping someone here, might have some pointers for me. I have looked behind the dash from the floor of the car, and I can see that they twist into the flat circuit board but I can't easily get my hand in there.

Thanks

Ken

_________________
Stock 75 Duster 109K. Working on Turbo setup.


Top
   
 Post subject:
PostPosted: Wed May 04, 2005 5:29 am 
Offline
Board Sponsor
User avatar

Joined: Wed Oct 23, 2002 7:54 pm
Posts: 658
Location: Hutchinson, MN
Car Model:
The first rule before you poke around under the dash is to disconnect the battery. The amp gauge has power to it all the time and it has exposed terminals on back of the instrument cluster. There might also be a few other live circuits behind there too.

It will be easiest to remove the instrument cluster to change the bulbs. Also those twist-in light sockets like to break the plastic ears off and then they will not stay in. There are a couple different designs, some have good sturdy plastic ears, others just fall off with age.

To remove the instument cluster... Block car wheels so it will not roll, disconnect the battery, lower the steering column (remove bolts from filler panel at floor so it can move around, then remove nuts under column at dash, then let it settle itself down to the seat, may also be useful to put auto trans lever in neutral but block the wheels to car does not roll away), disconnect speedometer cable from back of speedometer (I think there is a plastic tab to squeeze to release it) , remove screws holding instrument cluster to dash, then carefully pull away a little bit, disconnect several plug in wire connectors and last if you still don't' have enough access is to remove the nuts holding wires to the amp gauge, then the cluster will be free to take to the work bench.


Last edited by Craig on Wed May 04, 2005 7:18 pm, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Wed May 04, 2005 6:56 am 
Offline
Board Sponsor
User avatar

Joined: Tue Jul 08, 2003 11:33 am
Posts: 2378
Location: Central GA
Car Model: Many & varied, including stock & hopped up /6's
...or phone ET and ask him to come change those bulbs for you! :)

D/W

_________________
Image
If it ain't broke, fix it!


Top
   
 Post subject:
PostPosted: Wed May 04, 2005 2:54 pm 
Offline
2 BBL ''SuperSix''
User avatar

Joined: Mon Mar 08, 2004 9:38 pm
Posts: 22
Location: Cincinnati, Ohio
Car Model:
Thanks for the help guys..

_________________
Stock 75 Duster 109K. Working on Turbo setup.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 4 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited