Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Tue Nov 17, 2026 7:36 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Mon Oct 24, 2005 4:34 am 
Offline
EFI Slant 6
User avatar

Joined: Wed Apr 20, 2005 5:22 am
Posts: 491
Location: Missouri City, Texas (Houston Area)
Car Model:
How do you tighten a Harmonic Balancer with the pan on? It requires 135 ft lbs of torque and I was wondering how you keep the motor from turning while you tighten the HB.

Thanks,

bwhitejr


Top
   
 Post subject: Hammer It
PostPosted: Mon Oct 24, 2005 8:03 am 
Offline
EFI Slant 6
User avatar

Joined: Thu Aug 12, 2004 9:21 pm
Posts: 297
Location: San Diego
Car Model:
i usually just hit with my 1/2" impact. i have gotten a feel for what is good enough. if you don't have an impact. pull the starter and stick a big screwdriver or a pry bar on the ring gear to keep it from spinning. good luck.

zedpapa

_________________
1970 dodge dart w/225 /6 bored .040" over, holley 390cfm w/vac. sec., compcams 252s, clifford shorty headers w/2.5" exhaust w/flowmaster, f-body 11" front discs, aluminum A-833OD, 8 1/4 w/3.21 SG
soon to have 5 gears!!!


Top
   
 Post subject:
PostPosted: Mon Oct 24, 2005 8:10 am 
Offline
Supercharged
User avatar

Joined: Sat Nov 27, 2004 8:03 pm
Posts: 10443
Location: IRWIN PA
Car Model:
I have been running mine for a few years with just the "press Fit"

I press it on with a bolt and washers that I stole from a 318. - The Impact wrench works real well for me..



Greg

_________________
http://www.youtube.com/hyperpack

Image


Top
   
 Post subject:
PostPosted: Mon Oct 24, 2005 8:59 am 
Offline
Turbo EFI
User avatar

Joined: Tue Mar 11, 2003 5:09 am
Posts: 1167
Location: Troy, Texas
Car Model:
Mine doesn't have a bolt. Drove it on with a block of wood and 2 lb sledge hammer. :shock:

Jerry

_________________
There's a difference between ignorance and stupidity.
Ignorance is not knowing any better.
Stupidity is knowing, yet doing it anyway.


Top
   
 Post subject:
PostPosted: Mon Oct 24, 2005 9:43 am 
Offline
Board Sponsor
User avatar

Joined: Sat Feb 08, 2003 2:37 pm
Posts: 4194
Location: CA
Car Model:
Jerry - I did the same thing too while my engine was on the stand. I was told by some friendly folks here that thats not a good idea unless the engine is standing on the other end of the crank as it could cause thrust bearing damage.


Top
   
PostPosted: Thu Oct 27, 2005 7:32 am 
Offline
EFI Slant 6
User avatar

Joined: Wed Apr 20, 2005 5:22 am
Posts: 491
Location: Missouri City, Texas (Houston Area)
Car Model:
When installing a harmonic balancer. I have heard that you are supposed to put RTV on it so it will seal properly. How does that work? What is the proper way to install the HB?

bwhitejr


Top
   
PostPosted: Thu Oct 27, 2005 8:48 am 
Offline
Turbo Slant 6
User avatar

Joined: Mon Apr 04, 2005 12:22 pm
Posts: 580
Location: Austin Texas
Car Model:
Quote:
When installing a harmonic balancer. I have heard that you are supposed to put RTV on it so it will seal properly. How does that work? What is the proper way to install the HB?

bwhitejr
For heaven's sake, DON'T put RTV anywhere on it. Coat the snout of the crankshaft LIGHTLY with motor oil, then torque it down with an impact wrench until its fully seated.

_________________
Image


Top
   
 Post subject:
PostPosted: Mon Oct 31, 2005 12:34 pm 
Offline
Turbo EFI
User avatar

Joined: Tue Mar 11, 2003 5:09 am
Posts: 1167
Location: Troy, Texas
Car Model:
Pierre, I've heard that recently, too. Unfortunately, it's too late to worry about it now. The engine starts right up and runs fine, for now. Of course, we just got the car back from the paint shop and haven't put everything back together, so it can be put on the road for a test run.

bwhitejr, the only thing I put RTV sealant on was a harmonic balancer hub repair micro-sleeve. Sounds complicated, but it's not. If you check the outer surface of the hub that slips through the front oil seal (located in the timing chain cover), you may find a shallow groove worn by years of contact with the seal. Doesn't seem right, rubber wearing out the metal, but it happens. Your local parts supplier can probably get you a micro-sleeve that simply slips over the hub to provide a brand new surface for the front seal to press against. The instructions for the sleeve say to use RTV sealant when installing it on the hub. My guess is it's for lubrication and also to make sure no oil seeps by between them. MAKE SURE you don't crush the VERY thin micro-sleeve. Go slowly, and make sure you put it on straight and evenly.

Jerry

_________________
There's a difference between ignorance and stupidity.
Ignorance is not knowing any better.
Stupidity is knowing, yet doing it anyway.


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 8 posts ] 

All times are UTC-08:00


Who is online

Users browsing this forum: No registered users and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited