Slant *        6        Forum
Home Home Home
The Place to Go for Slant Six Info!
Click here to help support the Slant Six Forum!
It is currently Sat Nov 21, 2026 11:23 pm

All times are UTC-08:00




Post new topic  Reply to topic  [ 26 posts ]  Go to page Previous 1 2
Author Message
 Post subject:
PostPosted: Sun Jul 11, 2004 5:57 pm 
Offline
SL6 Racer & Moderator
User avatar

Joined: Sat Oct 19, 2002 12:06 pm
Posts: 9094
Location: Silver Springs, Fl.
Car Model:
The previous post was from me. Had to go to backup computer, and forgot to log on. One other thing of note. Due to manufacturing tolerances, I have yet to find a 170 at zero deck. All have been between .010-.025 down the hole. Also the factory head gasket, was a steel shim type, at .022.

_________________
Charrlie_S
65 Valiant 100 2dr post 170 turbo
66 Valiant Signet 170 nitrous
64 Valiant Signet
64 Valiant 4dr 170
64 Valiant 4dr 225


Top
   
 Post subject: Not alone...
PostPosted: Mon Jul 12, 2004 4:46 am 
Offline
Turbo Slant 6

Joined: Tue Mar 16, 2004 6:25 am
Posts: 831
Location: Tompkinsville, KY
Car Model:
heckshemi, I'm with you; I've been doing a "paper" long rod 170, and trying to get the numbers to work out. I can't wait to hear that little motor sing! And hey, someone said the block is 50# lighter, so great handling, too!
The deck height misprint is everywhere, like panic says, but the block really is an inch and a half shorter, as verified by Charlie and Hypervaliant.
The 2.5 stuff looks good to me;
86-88 rod = 6.179 c to c, 1.014 big end width, 1.969 journal
(Newer rods are shorter because they did the common block trick)
Not as strong as your Carillo or as light, but at least they're pure :wink:
2.5 turbo piston = 1.335 comp height
Small end is a match, they're designed for each other.
This piston has a dish, don't know the depth yet.
This combo ends up .0115 positive, which should be an easy mill for whatever deck you want, reducing the dish volume at the same time. A little dish left will hopefully promote a good burn, while increasing crown surface area for a little extra push.
The crank issue has held me back because of the cost, but if Doc's idea really works, stand back!
Doc, when did you use that journal trick? No durability/oil control problems?

_________________
O==\=/==O

"A mechanic is Somebody."
- Jim Preston


Top
   
 Post subject:
PostPosted: Mon Jul 12, 2004 10:24 am 
Offline
Guru
User avatar

Joined: Sat Oct 12, 2002 11:22 am
Posts: 3740
Location: Sonoma, Calif.
Car Model: Many Darts and a Dacuda
I have seen a "journal in a journal" done on a couple of different cranks, one was a V8, the other was an inline 4. (never on a SL6)
I've never run one myself so I don't know about the durability issue.

The key would be to maintain the connecting rod side clearance for oil control, there is enough meat on our SL6 crank to do that with ease.
I would also put a radius in the corners to reduce the chance of cracks starting.
DD


Top
   
 Post subject:
PostPosted: Wed Jul 14, 2004 6:10 am 
Offline
TBI Slant 6

Joined: Mon Jan 12, 2004 11:20 am
Posts: 196
Location: Long Island, NY
Car Model:
Maybe someone typo'd it: 9.68 was suppoesd to be 9.068?
That would make more sense - the 170 would have NO compression with the piston that far down.

_________________
Image


Top
   
 Post subject:
PostPosted: Tue Nov 08, 2005 2:47 pm 
Offline
EFI Slant 6
User avatar

Joined: Sun Jan 11, 2004 11:19 am
Posts: 255
Location: Oulainen, Finland
Car Model: 1965 Valiant 170/A833/8 3/4SG
Hey heckshemi, any progress with the 170?

I was thinking of building high revving long rod turbo 170.
With quick calculating vw bug 88mm piston and a Ford 5.932" rod would be close to stock height.


Top
   
 Post subject:
PostPosted: Wed Nov 09, 2005 1:12 pm 
Offline
TBI Slant 6

Joined: Fri May 30, 2003 4:32 pm
Posts: 131
Location: Northwest FL
Car Model:
Progress has been slow. I got the crank machined. It turned out real nice. The rods are bushed. The block has been bored .104" over. I've got most of the parts together. Working on a "special" head now.
I'm thinking the '64 Dart may be to heavy for the 170 so I'm also building a 225 for it. The 170 will go in a '61 Valiant.
I'll try to post some pics.

_________________
Franklin
'61 Valiant


Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 1:19 pm 
Offline
EFI Slant 6
User avatar

Joined: Sun Jan 11, 2004 11:19 am
Posts: 255
Location: Oulainen, Finland
Car Model: 1965 Valiant 170/A833/8 3/4SG
I bought a set of 6 Ford 4.6 V8 Carrillo rods. 8) Pic
Talked to my machinist yesterday. He wanted to enlarge the big end to match original slant size and use slant rod bearings. That way I could use stock crank.
Edit: Changed a bigger picture


Last edited by MJF on Wed Nov 16, 2005 5:55 am, edited 1 time in total.

Top
   
 Post subject:
PostPosted: Fri Nov 11, 2005 9:36 pm 
Offline
Guru
User avatar

Joined: Sat Oct 12, 2002 11:22 am
Posts: 3740
Location: Sonoma, Calif.
Car Model: Many Darts and a Dacuda
Quote:
Progress has been slow. I got the crank machined. It turned out real nice...
I'll try to post some pics.
Did you weld and grind or simply grind the new journal inside the current one?
DD


Top
   
 Post subject:
PostPosted: Mon Nov 14, 2005 6:50 am 
Offline
Board Sponsor & Moderator
User avatar

Joined: Mon Oct 21, 2002 11:08 am
Posts: 17689
Location: Blacksburg, VA
Car Model:
Mike Jeffrey runs Chevy rods with the Slant crank machined down in the middle for a journal-in-journal.

I am contemplating a similar buildup with ~6" rods and pistons from a Mopar 2.0-2.4L.

I like the looks of the Carillo 4.6 rod. I can't make out the C-C length on your sheet though.

I also like the thought of 2.2L or 2.5L rods with closer big ends to the Slant dims.

Lou

_________________
Home of Slant6-powered fun machines since 1988


Top
   
 Post subject:
PostPosted: Mon Nov 14, 2005 9:04 am 
Offline
EFI Slant 6
User avatar

Joined: Sun Jan 11, 2004 11:19 am
Posts: 255
Location: Oulainen, Finland
Car Model: 1965 Valiant 170/A833/8 3/4SG
Center to center is 5.932. I was looking Wiseco 88mm pistons. Listed to Toyota 3TC.


Top
   
 Post subject:
PostPosted: Mon Nov 14, 2005 10:09 am 
Offline
TBI Slant 6

Joined: Fri May 30, 2003 4:32 pm
Posts: 131
Location: Northwest FL
Car Model:
I had them machined down the middle as "journal in a journal" as you suggested, Doc. Turns out they were nascar rods with honda size journals so there was plenty of meat on the crank for side support.

_________________
Franklin
'61 Valiant


Top
   
Display posts from previous:  Sort by  
Post new topic  Reply to topic  [ 26 posts ]  Go to page Previous 1 2

All times are UTC-08:00


Who is online

Users browsing this forum: Amazon [Bot] and 8 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Limited